Can Draw-Tite QSP Trailer Hitch Silencer and Cover be Used with Reese SC Weight Distribution

Question

Question:

Can it be used with a Reese SC

asked by: Christopher

0

Expert Reply:

I spoke with my contact over at Draw-Tite and he said that you can use the QSP hitch silencer # 63080 with a Reese SC weight distribution system. But you would want to take the cover off by removing the pin because it could cause interference in some cases.

This device will fit Draw-Tite, Hidden Hitch, and Reese 2 inch trailer hitches and we have confirmed that it also fits a Curt 2 inch trailer hitch. But it is not a fit for factory installed trailer hitches.

expert reply by: Michael H

0

Answer 1

The Draw-Tite QSP Trailer Hitch Silencer and Cover for 2" Hitch Receivers #63080 will definitely work when towing to help eliminate the rattle, though it won't be quite as effective as other options. Just keep in mind that this is…

view full answer...

Answer 2

Due to how the rack is configured with the square bars fitting inside its towers, the weight isn't supported outside the towers on the Malone SteelTop Roof Rack #MPG202 with the same efficacy that it is inside the towers. Due to that Malone…

view full answer...

Answer 3

I do have an option for you but there would be no way for me to confirm the Draw-Tite QSP Trailer Hitch Silencer part #63080 will work with a factory trailer hitch as it is designed especially for the Draw-Tite Trailer Hitch Receivers. That said,…

view full answer...

Answer 4

For your ball mount or accessory you can use the Draw-Tite QSP Trailer Hitch Silencer and Cover for 2" Hitch Receivers #63080. The Blue Ox Hitch Receiver Immobilizer II - 2" Hitches #BX88224 will keep the carrier from moving…

view full answer...

Answer 5

While there are portions of the Draw Tite QSP part #63080 that are plastic the mechanism that removes the rattle is actually made of metal as plastic would not be strong enough to hold the hitch accessory tight enough. This is supposed to be only…

view full answer...

Answer 6

Running the power wire to the battery when installing Curt trailer wiring harness #C56350 on your 2014 Toyota RAV4 is not all that difficult, it can just take some time depending on how you want to route the wire. How much time it takes varies. There…

view full answer...

Answer 7

What is probably happening is that the collar around the receiver opening on the Curt hitch has a very thick powder coat that is preventing the Draw-Tite QSP #63080 from fitting properly. If you were to sand away some of the powder coat on the collar…

view full answer...

Answer 8

There is a trailer hitch receiver that is going to give your 2016 Toyota RAV4 a bit more clearance than the Curt Trailer Hitch Receiver #C13149 you currently have installed, which is another hitch from Curt: - Curt Trailer Hitch Receiver #C13406 When…

view full answer...

Answer 9

The hitch for your 2018 Toyota Rav4 that has the best ground clearance is the Curt part #C13406 as it sits the highest and also because only the hitch opening hangs below the rear bumper which means turning into an elevation change like a steep…

view full answer...

Answer 10

The Curt hitch part #C13406 actually has an open back so there isn't a limit to how far an accessory could insert into it.

view full answer...

Answer 11

I compared ground clearance measurements for all of the 2" trailer hitch receivers we have for your 2017 Toyota RAV4 and found that the Curt Trailer Hitch Receiver part #C13406 has a great clearance from the ground to the top of the hitch…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Can Draw-Tite QSP Trailer Hitch Silencer and Cover be Used with Reese SC Weight Distribution

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching