Fit of Curt Class I Trailer Hitch # C11393 on a 2010 Mazda 3 Sedan

Question

Question:

I would like to purchase a hitch receiver for my 2010 Mazda 3 Sedan regular trunk - not hatch back. I wanted to confirm the c11393 receiver will work with my car prior to purchasing. If there are any issues, how easy is return? Thanks

asked by: Kirstin B

1

Helpful Expert Reply:

The Curt Class I hitch you referenced, part # C11393 is indeed a fit for your 2010 Mazda 3 Sedan.

If you click the provided link, you can see our Returns Policy. I've also linked you to the installation instructions and a video showing the hitch being installed on a 2012 Mazda 3.

expert reply by: Mike L

1

Answer 1

Based on what you have described the aluminum carrier should have no problem handling the 200 pound estimated weight of the carrier and boat/motor combined. You will just need to make sure not to exceed the capacity of the trailer hitch on your 2010…

view full answer...

Answer 2

The Curt light-duty Class I trailer hitch receiver you referenced, part #C11393, is a fit for the sedan versions of the 2010-through-2013 Mazda 3 with or without LED taillights. This particular hitch fits no other vehicles. The hitch comes with all…

view full answer...

Answer 3

All three components of the Rhino Rack part numbers #RRVA118B-2, #RRRLKVA, and #DK289 would be needed. The bars, the feet, and the adapter kit that attaches the feet to the factory fixed mounting holes of the roof of the vehicle.

view full answer...

Answer 4

The Curt Trailer Hitch Receiver #C11393 will not contact the exhaust on your 2012 Mazda 3 sedan.

view full answer...

Answer 5

You have done your research. As you have seen, all of the hitches for the 2010 Mazda 3 are Class I trailer hitches. The Draw-Tite and Hidden Hitch models do have the safety notch in them that prevent the insertion of a Class II accessory. This is so…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...

Answer 10

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 11

Yes, the Curt hitch part #C77ZV is a fit for the 2023 Toyota Crown Hybrid. I attached a link to the install instructions as well as a link to an installer finder in case you wanted to find someone near you to install the hitch.

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Fit of Curt Class I Trailer Hitch # C11393 on a 2010 Mazda 3 Sedan

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching