Will Fulton XLT Trailer Winch # F142425 Fit Mounting Plate on EZ-Loader Trailer

Question

Question:

My mounting plate is standard for easy loader trailers....does the XLT fit my mounting plate ?

asked by: Steve D

0

Expert Reply:

Most trailer winch mounts feature multiple sets of mounting holes to allow just about any winch to install properly. This is because a winch will deliver its rated line pull only if it is installed correctly as per the manufacturer instructions.

The Fulton XLT # F142425 has an industry-standard 3-point mounting bolt pattern. This is compatible with the mounting plate on your Easy-Loader trailer according to my contact at Fulton.

expert reply by: Adam R

0

Answer 1

3/8 inch diameter Grade 5 or higher hardware would be what you'd need to mount the Fulton XLT winch part #F142425 that you referenced. A total of 3 bolts would be all you'd need.

view full answer...

Answer 2

The Fulton XLT 2-Speed Trailer Winch - 10" Long Handle - 20' Strap - Zinc - 3,200 lbs #F142425 will be able to be used on your application and winch stand set-up without any obvious issues. As long as you have clearance for the…

view full answer...

Answer 3

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need…

view full answer...

Answer 4

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 8

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 9

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 10

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...