Fulton F2 Winch Compatibility With Winch Stand On Boat Trailer

Question

Question:

Will we run into any issues with the Fulton XLT winch with our current winch stand set-up?

asked by: Jim A

0

Expert Reply:

The Fulton XLT 2-Speed Trailer Winch - 10" Long Handle - 20' Strap - Zinc - 3,200 lbs # F142425 will be able to be used on your application and winch stand set-up without any obvious issues. As long as you have clearance for the handle, you won't have any compatibility issues.

expert reply by: Jason S

0

click to enlarge

Answer 1

The Ark Ezi-Guides Self-Aligning Boat Trailer Loading System part #AR64FR has rollers which measure 14" long. I have attached a photo below with this measurement. Unfortunately this system will not work on a angled back section, it requires a…

view full answer...

Answer 2

I attached a diagram that shows how tandem axle trailer brakes get wired up. What's great is that for trailer brake magnets either wire can be used as the power or ground wire. The second picture I attached show which direction brake assemblies…

view full answer...

Answer 3

You'd look from the rear of the vehicle. Basically the left side of the axle is driver side and the right side is the passenger side.

view full answer...

Answer 4

The right and left orientation is determined if you are standing behind the trailer looking towards the tow vehicle. The left side is the drivers side and the right side is the passengers side. Tthe shorter brake pad will always be in the front of…

view full answer...

Answer 5

Finding the right capacity winch for your boat trailer is fairly simple but you have factors that must be taken into consideration. Boat-size-to-winch capacity is generally 2 to 1. With good rollers and short winching distances, you could increase…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Fulton F2 Winch Compatibility With Winch Stand On Boat Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching