Availability Of 5-5 1/2 Inch Hub Assembly, Spindle, Bearings Rated For 1,750 lbs. Each

Question

Question:

What I would like is a set of hubs pattern 5 on 5 1/2 which I found but hard to find the spindles I need to match the bearing size can you work up a package price for 2- Hubs bolt pattern 5 on 5 1/2 with spindles that fit say rated at 1750lbs each or combined 3500 lbs rating? If you can give me the options also such as round, square and with brake backing plate mount I would appreciate it.

asked by: jim K

0

Expert Reply:

I have the Dexter Trailer Hub Assembly - 3,500 lbs Axles - 5 on 5-1/2, # 84555UC1, which is rated at 1,750 lbs. each. The bearings, races, cap and seal included.

The only other option I would have is the Dexter Trailer Hub & Drum Assembly - 3,500 lbs. Axles - 5 on 5-1/2, # 84557UC3, if you were wanting brakes. The capacity is 1,750 lbs. and comes with a 10 inch X 2-1/4 inch drum. It also comes with bearings, races, cap and seal.

The spindles that are available for both hub assemblies with the 1,750 lbs capacity are the TruRyde round Spindle # TRU64FR, which is a 8-1/4" long spindle, the TruRyde square Spindle # TRU47FR, which is an 8-1/4" long spindle, or the TruRyde round Spindle # TRU84FR, which is an 11-1/4" long spindle.

If you are wanting brakes you can use the #84 EZ Lube round Spindle, # TRU74FR. It comes with a brake mounting flange. Then you can use the Dexter Trailer Hub Assembly, # 84557UC3, that I mentioned above, but you would need to add the TruRyde Grease Cap, 1.986 inch OD EZ Lube Drive in with Plug, # RG04-040, and the TruRyde Grease Seals 10-19 (pair), # RG06-050.

expert reply by: Jeff D

0

Answer 1

For your Shelby 5856A boat trailer, I recommend the Fulton Bolt-Thru Swivel Marine Jack with Dual Wheels - Sidewind - 12" Lift - 1,500 lbs #FXPD15L. This jack has zinc plating for corrosion resistance and durable poly wheels. For the single…

view full answer...

Answer 2

To replace your Shelby 5856A jack I recommend the Fulton Round Snap-Ring Swivel Marine Jack #FTJ120W0301. We have had customers say that this fits the mounting plate for the Shelby 5784A perfectly. This jack features a lift capacity of 1,200 pounds,…

view full answer...

Answer 3

To replace your Shelby 5856A jack I recommend the Fulton Round Snap-Ring Swivel Marine Jack #FTJ120W0301. We have had customers say that this fits the mounting plate for the Shelby 5784A perfectly so ti's going to be the easiest install possible.…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...