Trailer Hitch Availability for 2013 Dodge Avenger R/T with Dual Exhaust

Question

Question:

looking for a trailer hitch for a 2013 dodge avenger r/t with dual exhaust my dealer says they dont make one? i dont think they know what they are talking about can you help? thanks

asked by: R C

0

Expert Reply:

We do have several choices for you in a 1-1/4-inch Class I hitch for your 2013 Dodge Avenger R/T with Dual Exhaust. These can be seen on the link provided for you. I checked with my technical contact at Hidden Hitch and Draw-Tite and your dual exhaust R/T is fully compatible with these light-duty hitches.

If your intended use for the hitch is to install a bike carrier, then the hitch I suggest is the Draw-Tite # 24871. Unlike the Curt model # C11133 this hitch does not require you to use a stabilizing strap # 18050, which Curt requires for you to maintain your hitch warranty. The Draw-Tite warranty does not include this requirement.

Installation of the Draw-Tite # 24871 requires no drilling, only temporary lowering of the exhausts for installation. I have linked a complete installation video and a helpful article for you to simplify your installation. You will need only a torque wrench in addition to basic hand tools. All required hardware is included.

A Class I hitch can be used with a compatible Class I accessory, such as a 2-bike hitch rack or a lightweight cargo carrier. Links to both of these product categories are provided along with articles to help you select compatible products that will fit well at the rear of your Avenger.

expert reply by: Adam R

0

Answer 1

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 4

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 5

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 8

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 9

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 10

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 11

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...