Trailer Hitch for a 1997 Toyota Camry LE

Question

Question:

Please, tell me what hitch I need to buy for a Toyota Camry LE year 1997. It has 4 cylinders and 4 doors.

asked by: Alex

0

Expert Reply:

I would recommend the Draw-Tite Class II Draw-Tite Hitch, part # 36336. It is the most popular hitch we sell for your vehicle.

expert reply by: Sarah

0

Answer 1

I have reviewed the installation instructions for the Draw-Tite Class II hitch, part number 36336. There is no indication of cutting the fascia or bumper for the 1999 Toyota Camry. The receiver opening sits flush with the rear fascia or bumper…

view full answer...

Answer 2

There are 2 holes that have to be drilled in the bottom of the frame to install Curt trailer hitch #C12339 on your 2000 Toyota Camry. I have included a link to the installation instructions for you so you can see the installation steps. I have also…

view full answer...

Answer 3

The CE Smith Boat Trailer part #CE48810 would be a great option for your Sportsman AutoPilot 120 as it's 12 feet long like what this trailer was designed to fit and this has adjustable angle and width bunks to best match the hull of your…

view full answer...

Answer 4

The trailer hitch I recommend for your 2005 Camry is the Draw-Tite Trailer Hitch, part #36336. The price of this hitch will certainly not scare you. This is a Class ll hitch and it has a 1-1/4 inch receiver opening. I have attached a link to an…

view full answer...

Answer 5

In addition to the Draw-Tite Trailer Hitch, #36336, and a ball to fit the coupler on the trailer you plan to tow (#19256 for 1-7/8 in diameter or #19258 for 2 inch diameter), I also recommend ball mount part #36061 and T-One Vehicle Wiring Harness…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Trailer Hitch for a 1997 Toyota Camry LE

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching