Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
TPMS individually monitors the tire pressure and temperature of your RV's tires. The monitor can store data for up to 4 vehicles. The flow through design lets you inflate tires without removing sensors from valve stems.
Features:
Specs:
While on the road, it is very important to regularly maintain your tires and make sure they're inflated correctly. If your tires are underinflated or overinflated, they'll develop irregular tread wear and become prone to overheating and blowing out. The TireMinder i10 TPMS helps protect your investment and keep your family safe by monitoring your tires and alerting you of any signs of danger before disaster strikes.
This TPMS includes 4 flow through sensors that let you individually monitor each tire on your application for changes in pressure and temperature. The flow through design allows you to inflate or deflate your tires without having to remove the sensors. These brass sensors are able to work on rubber, steel, chrome, or nickel valve stems. Every 6 seconds, they will check the pressure and temperature again.
The color LCD monitor will provide you with visual and audible cues to warn you of dangerous changes in tire pressure and temperature, as well as alert you of changes with the monitor battery, sensor battery, and sensor signal. Before you begin setup, make sure the monitor has been charged and the repeater and sensor batteries have been installed.
Select your RV or trailer configuration or the locations of the tires you want to monitor. Then select one tire location, install a sensor on the corresponding tire on your RV or trailer, and the current PSI will automatically appear on the screen. With the purchase of additional sensors ((TM66FR - sold separately), you can monitor up to 20 tires, which is perfect for a fleet. This system can display up to 10 tires at a time, alternating between the tires of the "front" or drivable application and the tires of the "rear" or towable application. Sensors can be added, moved, deleted, or replaced at any point, even after initial installation.
You can set the tire pressure in psi, Bar, and KPa. If you choose psi, you can set the tire pressure anywhere from 0 psi to 199 psi. As for the temperature, you're able to switch between degrees F and degrees C, and the system will alert you if the temperature exceeds 167 degrees F. With the app, you are also able to disconnect and reconnect to different vehicles, RVs, or trailers. This is useful for those who switch between different applications, such as a Class A motorhome who sometimes tows a car. It also can store pressure and temperature information for up to 4 vehicles, or 40 tires.
This Bluetooth repeater helps improve signal strength and range of the sensors, especially for longer RVs, trailers, and other applications. It ensures that the link from the sensors to the monitor is strong and continuous.
This TPMS system includes 8 batteries, 4 locking nuts, 4 O-rings, and a wrench. Once the batteries have been inserted and covers have been re-installed, remove the cap of your valve stems, thread the locking nuts onto the valve stems, and install the sensors. Lastly, secure the locknuts against the sensors with the wrench.
The weatherproof and dustproof Bluetooth repeater can be installed anywhere on the exterior of your RV or trailer between the rear axle and king pin. The optimal mounting location for a towable camper is toward the front whereas the optimal mounting location for a drivable RV is toward the rear. it is not recommended to install the repeater inside your vehicle, as you might experience signal blockage. Use either the adhesive (included) or hardware (not included) to attach the repeater and wire it to a power supply line. In order to reduce vibration, make sure it's securely mounted. Then connect the black wire to ground, and the red wire to power.
Average Customer Rating: 4.7 out of 5 stars (6 Customer Reviews)
TPMS individually monitors the tire pressure and temperature of your RV's tires. The monitor can store data for up to 4 vehicles. The flow through design lets you inflate tires without removing sensors from valve stems.Works great & give me piece of mind. My only complaint is the mounting holes for the booster are too small to fit most screws.
Product worked great. It gave me peace of mind knowing the tire pressure and temp on our trailer during a trip from Illinois to Alaska. This product alerted me to a high temperature and pressure condition on a 102 degree day in Wyoming last summer.
Loved it until the last sensor didn’t work. Spent almost 2hours swapping batteries, clearing starting over and swapping wheels! Still doesn’t connect to monitor.
By far superior to the several TPMS systems I've had -- most importantly, it samples all tires every 6 seconds and displays all pressures simultaneously, instead of individually. I'm excited!
prompt delivery
Works well. Definitely need to read and follow directions.
Do you have a question about this TPMS Sensor?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Jenny N.
8/2/2022
Thanks for reaching out! I would recommend doing a full or reset. This is helpful to determine the cause of this issue. After doing a full , if the same transmitter continues to not function properly, please do not hesitate to contact us. To the sensors please see the list below: 1. First, remove all transmitters from the valve stems and set them down by the tires. 2 From Monitoring Mode, press and hold the LEFT and RIGHT buttons for 5 seconds -until all 20 positions appear-. The screen will show LEARN in the top center of the display. You will see that all your currently active tire positions display a tire pressure. 3. Press and hold the CENTER and RIGHT buttons. After 5 seconds, the unit will beep twice, and each tire position will read - -. Since you are already in the Learn Mode, you may start the re-install process immediately. If you are not ready, you should exit from this mode by pressing and holding the LEFT and RIGHT buttons until all 20 positions disappear. 4. You will be back in Monitoring Mode From here, you may start over at any time.