Summer Starts Here - Save up to 70%
1" Diameter round. Mini LED trailer light serves as a side marker light or a clearance light. Pirhana series combines modern design with vibrant lighting. Recessed mount with included grommet. 2-Wire design. P2 rated.
Features:
Specs:
A P2-rated light produces a 45-degree angle of light to either side of its centerline for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side. So this type of light can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, then you must install 2 separate lights on your trailer - one as a front or rear clearance light and one as a side marker light.
Recessed-mount trailer lights install with a grommet, which is often sold separately. These lights extend past the trailer surface and require a hole for installation. If replacing a light, you can utilize the pre-existing hole. If installing a new light, you will need to cut a hole or use a mounting bracket (sold separately) to complete the installation.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi there trailer owners today, we're going to be taking a look at Peterson's Pirana mini LED side marker and clearance lights. These lights are available in either an Amber color for your side markers or red for clearance lights at the back of your trailer. These are going to be a great upgrade if you've got limited space or need low profile side marker, or clearance lights on your trailer. They don't take up very much, they're about an inch in diameter and they just press in, they have a grommet. So it's like a lot of your trailer lights, except for these are significantly smaller. And these are an upgrade because they're going to be brighter than your incandescent lights, which take up more space, stick out, farther, use more power, and don't last as long.
So you can upgrade to an LED one here. That's going to last significantly longer, provide more visibility at night, and not take up very much real estate. It really modernizes it being nice and flush against the trailer.We're going to start our installation by removing our old marker light. We're going to be replacing it with this newer, smaller, lower profile LED light. There's just a single stud here on the back that has a nut on it for this light.
I'm just going to remove that, in a lot of cases this is just going to break off these old incandescent lights are pretty common of just having rust issues and stuff like that. So we can just set that guy aside. We're not going to install the new light into here, but you can see that the hole there's going to be too small. So we're going to use a step bit to enlarge this hole until it's big enough for our light to pass through. And this is just a press fit.
So once we get it drilled out properly, it's just going to poop pop in there. So here's our step bit. We're just going to enlarge it until it fits. This is the easiest way to do it, to ensure that you get a good tight fitSo we're just going to do a quick check. We're still not quite there.
So now that we've got it drilled out to the right size we can see it's going to be snug, but if we give it a push, we should be able to get this in here. And we want it to be nice and snug so that's kind of what we're looking for. It's a little bit too snug, we might need to just go back in there real quick and just hit it just to clean up some of the rougher edges. Once we get it nice and flush and to where it holds in there nice and solid. We've now got that installed and we just need to hook up our wiring. We stripped it back and then placed a ring terminal on it. You can get ring terminals here at etrailer, we're then just going to ground this wire by running it right into the frame. And we can do so right here.The brown wire that's passed through the small hole here is our running light circuit. So we had just stripped that back. So we got a nice clean connection point to it. And we're just going to connect the black wire from our white, to the running light circuit on our trailer. We're using heat shrink butt connectors to do this, which are available here at etrailer. To ensure that we don't get any moisture entering down to our wires, which can cause corrosion. So we're not going to take our heat gun to shrink that connector down. I'm just going to keep out all that moisture.And then if you picked up any red marker lights for the rear of your trailer, they're going to install exactly the same. So we've gone ahead and installed some here at the back. And we installed some on the side, which we're Amber for closer to the front of our trailer. Now that they're installed, we're just going to hook up our test box. You can hook it up to your truck, turning your tail lights and make sure everything's working properly. So here you can see our rear marker lights are working properly and our Amber ones are good to go as well. And that completes our look at Peterson's Pirana mini LED side, marker and clearance lights.
Average Customer Rating: 4.8 out of 5 stars (275 Customer Reviews)
1" Diameter round. Mini LED trailer light serves as a side marker light or a clearance light. Pirhana series combines modern design with vibrant lighting. Recessed mount with included grommet. 2-Wire design. P2 rated.Fast service and great communication
I change out a clearance light located on the front top drivers side of my 2017 Open Range Roamer 374BH. The light was not damaged upon arrival and arrived several days before they said it was going to be. It was easy to install. I waited till it got dark and tested it and it was brighter than the other side, so I will be changing the other side to match. Overall, very pleased with the product.
Great online services. Easy site to get around and fast delivery. Will use again
Always a pleasant experience when dealing with etrailer. Huge assortment of products and excellent customer service.
Yes very nice lights..great quality. Easy install..
Good bright light, good quality,
One of my favorite lights.
These are far better than the bland factory lights and are sealed very well.
The lights worked great for our Timpte hopper trailer.
Easy to install and fit holes from previous installation.
Not sure its anyones fault but the LED marker lights on my trailer fasten to the wall with screws and today that style is not made as it was in 2017...So i am rating the lights "average" cause till i open the light up without busting it I got to make it work and your lights are just the same as the rest...lights look fine and i will let you know how it works out...
Order 2 of theses paid extra for shipping , and they don't match each other dame part number , tried to return them wad going to cost me more thank just keeping the wrong parts does not match pictures on website
Good service fast shipping
These lights were the perfect brightness, very rugged, and easy to install inside protected areas of the frame on the updated raft trailer. etrailer has great selection, the website makes it easy to find the best parts for the job, and their communication is excellent. Their videos and reviews are invaluable.
came quick and was an exact match
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.