Loctite Threadlocker 262 - High Strength - Up to 3/4" Nuts/Bolts - 0.20-Fl-Oz Tube

See what our Experts say about this Loctite Lubricants Sealants Adhesives

• Is there a Way to Lock D-Ring Shackles to Front Of Jeep Wrangler Bumper
  Most Jeep guys leave the D-rings inside the Jeep or torque down the pins so tight that it would take a very determined thief to get them. You can also try a thread locker like the part # LT37420 to make them even harder to remove.
  view full answer...
• Securing Axle U-Bolts With Loctite
  Though it is not completely necessary to use something like Loctite's Threadlocker # LT37420, there wouldn't be any adverse affects either. Most U-Bolt kits do come with lock nuts making them more secure than standard nuts, but you can definitely apply # LT37420 to completely secure their purchase on the U-Bolts.
  view full answer...
• Anti-seize Product Recommendation to Install a Trailer Hitch on a 2007 Honda Fit Sport
  For Draw-Tite trailer hitch # 24776 for your 2007 Honda Fit Sport there isn't a specific recommendation for anti-seize products for the installation hardware. Loctite # LT37616 would work fine. But if you are talking about thread locker then there is just one thing to consider: how difficult do you want it to be to remove the hardware? If you use blue Loctite # LT37643 then the hardware can still be removed using hand tools. But if you use red Loctite # LT37420 then power tools would have...
  view full answer...
• What Color or Strength Loctite Do I Need to Install Wheel Studs?
  Yes, you will want to use the Loctite Threadlocker 242 - Medium Strength - 1/4" to 3/4" Nuts/Bolts item # LT37418 to install the Redline Replacement wheel studs item # 25-53. This is the blue one you will be able to remove your studs in the future if you need to replace them. The red Loctite Threadlocker 262 - High Strength - Up to 3/4" Nuts/Bolts - 0.20-Fl-Oz Tube item # LT37420 is the one you would either want to use or stay away from if you don't plan on removing the bolt.
  view full answer...
• Roadmaster Falcon All-Terrain Tow Bar Will Not Lock Into Place
  I spoke with my Roadmaster representative, and explained the problem you are experiencing. There is not a repair kit available for the problem you describe, but my rep told me that is sounds as if the anvil bolt on the end of the inner arm has come loose. This is a very simple repair. Remove the inner arm from the outer arm, and locate the anvil bolt on the end of the inner arm. Remove the bolt, and apply some red locktite (part # LT37420) to the threads and reassemble the arm. When this...
  view full answer...
• Lippert 6-Point Level-Up System Foot Pad Torque Requirement
  For the 6-point Level-Up System by Lippert, I made a call to the manufacturer to ensure you would receive correct information. Lippert said that when you bolt the footpads to the jacks, you need to torque them to 132 ft-lb. They said to make sure to use Loctite Threadlocker 262 - High Strength - Up to 3/4" Nuts/Bolts - 0.20-Fl-Oz Tube, # LT37420 on the footpad bolts and do not try to remove the bolt once it is tightened as removing the bolt could result in damage to the cylinder. It...
  view full answer...
• Is there a Draw-Tite Gooseneck Trailer Hitch for a 2006 Dodge Ram 2500 Diesel Mega Cab
  I spoke with my contact at Draw-Tite and she stated that Gooseneck Trailer Hitch, # 9464-35, will fit the diesel models of the 2006 Dodge Ram 2500 Mega Cab with a 6 foot bed. You may also need some Loctite Threadlocker, # LT37420, for installation if you do not already have some.
  view full answer...
• Installation Tips for the Replacement Gear Plate for Single and Double Coachstep
  We don't have an installation video for the Replacement Gear for Lippert Single and Double Electric Coach Step # LC301696 as of yet (March 2019) but I was able to track down some installation tips from Lippert for you. To replace the gear plate you need to first remove the entire Coachstep assembly. You will need to use a hex head wrench or hex head bit in a drill to remove the gear plate bolt. This is installed with some Loctite so you might need to apply some heat for the bolt to move....
  view full answer...
  
• Is Threadlocker Required To Install A Trailer Hitch Receiver?
  To install the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # C13119 or any hitch, there is not a requirement in the instructions to use any threadlocker, but I personally think it is wise. The instructions say to periodically check to ensure fasteners are tight, but I don't believe most people actually do that and Loctite Threadlocker 262 - High Strength - Up to 3/4" Nuts/Bolts - 0.20-Fl-Oz Tube # LT37420 would be a good idea.
  view full answer...
• Troubleshooting Wear On Folding Hitch And Recommendations For Hardware
  If your bolts are getting loose, I recommend using Loctite Threadlocker 262 - High Strength - Up to 3/4" Nuts/Bolts - 0.20-Fl-Oz Tube # LT37420 and torquing your bolts to the manufacturer specs. The Loctite will keep the bolts from coming loose and prevent further wear because of loose hardware. If you need to replace the unit you currently have due to the oblong holes, I recommend the Fulton Fold-Away Coupler Hinge Kit for 3" x 3" Tongue - Bolt On - Up to 5,000 lbs # FHDPB330301. Unfortunately...
  view full answer...
• Is Thread Locker Recommended Installation Hardware of etrailer Brand e98906 Trailer Hitch
  If the # e98906 hitch installation hardware is torqued according to the instructions, it won't be necessary to use # LT37420 thread locker. You can certainly do so if you wish, however please note that the torque specs mentioned in the installation instructions are for dry torque. If thread locker is used you'd use different torque specs (wet torque) which can be looked up online dependent on the size and class of the fastener.
  view full answer...
• Trailer Spare Tire Carrier Recommendation for Aluminum Side Wall on Utility Trailer
  For your Aluma Utility trailer with aluminum side walls, I recommend the Fulton Hi-Mount Spare Tire Carrier # FSTC1000301. This spare tire carrier is zinc plated so it won't have galvanic corrosion issues with your aluminum side wall and it has two plates to hold the back side of the carrier and disperse that pressure. Aluminum is a softer metal, so you will want to be careful when tightening to make it snug and yet not over-tighten and deform the side wall. If you want to make sure...
  view full answer...
  
• Installing A Replacement Foot Pad For Lippert Hydraulic Ground Control Level System
  The replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System - Qty 1 # LC324269 needs to be torqued to 132 ft-lb and Lippert recommends using some Loctite Threadlocker 262 - High Strength - Up to 3/4" Nuts/Bolts - 0.20-Fl-Oz Tube Item # LT37420 to prevent the bolt from loosening. You are correct with the placement of the washer and o-rings.
  view full answer...
• Should Loctite Be Used to Install a Curt Hitch on a 2014 Honda Odyssey
  There's no reason you couldn't use Loctite like part # LT37420 when installing the Curt hitch part # C13068 but as long as you torque the install hardware down to the proper torque figures in the instructions you wouldn't have any problems with the bolts loosening. I attached an install video for this hitch for you to check out as well.
  view full answer...
• Can You Use Loctite On The Andersen 5th Wheel Hitch Set Screws
  I spoke with Andersen and their tech stated that you can use some Loctite # LT37420 to help prevent the set screws on your Andersen Hitch # AM3200 from needing to be retorqued as often. He also stated you may need to replace the coupler, which you can get directly from them.
  view full answer...
• Will B&W Underbed Gooseneck Hitch # BWGNRK1000 Fit a 1996 Chevrolet 1500 With 8 Foot Bed
  The B&W Underbed Gooseneck Hitch, part # BWGNRK1000, will fit your 1996 Chevrolet C/K 1500 Truck with 8 foot bed. This hitch has a 30,000-lb gross towing weight capacity and a 7,500-lb tongue weight capacity. It is also recommended to use Loctite Threadlocker 262, part # LT37420, on all of the bolts when installing the B&W gooseneck hitch.
  view full answer...
• Base Plates That fit a Two-Door 1998 Chevy Tracker
  The correct base plates for your two-door 1998 Chevrolet Tracker are the Roadmaster XL Base Plate Kit - Removable Arms # 118-15. We do not have a video showing an installation of these plates, but the kit comes with everything you'll need except for Loctite Red # LT37420, which you'll use on all bolts when mounting the bracket. I've added a link to the instructions for you to take a look at; it's not a video, but it should provide you with a good idea of what the installation process...
  view full answer...
• Does Replacement Foot Pad LC324269 Have Torque Value
  The Replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System # LC324269 needs to be torqued to 132 ft-lb. Lippert also recommends using Loctite Threadlocker 262 # LT37420 to prevent the bolt from loosening.
  view full answer...
• Replacing Foot Pad On Lippert 6-Point Level-Up System - 132 Ft-lb Torque Requirement + Loctite
  I understand your concern. I called Lippert to verify that the 132 Ft-lb of torque and use of Locktite is still valid. They said that was the requirement and there were no alternative instructions. The assumption is that this is the method they used for installation and that by removing the foot pad you will run the risk of damaging the cylinder. If you need to remove it in the future the only way to release it after red Loctite is used would be by applying heat. I also verifed the order...
  view full answer...
  
• Fit of B & W Turnover Ball Gooseneck Hitch # BWGNRK1100 on 1997 Ford F350 w/ 8 Foot Bed
  According to our friends at B & W, their # BWGNRK1100 Turnover Ball Gooseneck Hitch you referenced will indeed fit your 1997 Ford F350 with the 8 foot bed. You shouldn't need to drill into the truck frame to install the frame rails. Using red Locktite thread locker, part # LT37420 is recommended on the installation hardware. To see the installation details, click on the provided link.
  view full answer...
• Diagnosing Reese 5th Wheel Rail Adapter For Ram OEM Prep Package That Is Rattling When Driving
  A small amount of rattle or play is normal for adapters like the Reese 5th Wheel Rail Adapter for Ram OEM 5th Wheel Towing Prep Package # RP30154. But you may need to tighten your adjustable anchor points as shown in the demonstration video that I attached (about the 5 minute mark). You may want to use some sort of sealant such as Loctite Threadlocker 262 - High Strength - Up to 3/4" Nuts/Bolts - 0.20-Fl-Oz Tube # LT37420 to keep the anchors where you want them.
  view full answer...
• Brake Assembly Stud Rotates when Trying to Tighten the Nut
  You might be able to drive out the one stud that is rotating, coat it with red Loctite such as # LT37420, let it cure, and then give it another try. Or you could tack weld it to the brake assembly to prevent it from turning. The threads must be a different pitch or size since the old ones are not fitting the new shocks. What I would do is take one of the new shocks or mounts or bolts with you to a hardware store and try out some nuts to find one that fits (unless Dexter can provide the...
  view full answer...
• Butyl Tape To Seal Trailer Roof Panel Joint
  The LaSalle Bristol XTRM Butyl Tape part # 344270341411-1 can definitely be used to seal the joint on the roof your cargo trailer. Butyl tape is used to seal off many roof accessories like trailer vents and fans. Since the butyl tape is pre-formed it is easier to install and get a water tight precise seal compared to some of the liquid sealants that can be more difficult to maneuver. The adhesive on the tape forms a bond with the surface that improves over time. This particular butyl tape...
  view full answer...
  
• Loc-Tite for Tightening U-Bolt Nuts of U-Bolt Kit
  You can use Loc-Tite if you would like when tightening the nuts of your U-bolt kit. It's not required but it won't hurt. The torque specs for 9/16 diameter U-bolts like the # APUBR-9 is 65-95 ft lbs. With that amount of torque on the nuts they would not back off. For Loctite you could use the part # LT37420.
  view full answer...

Do you have a question about this Lubricants Sealants Adhesive?