Installing A Replacement Foot Pad For Lippert Hydraulic Ground Control Level System

Question

Question:

what order do the steel washer and the 2 o rings go on the bolt? My guess is that the steel washer goes on, and then an o ring, and then the actual foot pad, and then another o ring? And how tight should the bolt be in ft lbs? Thanks!

asked by: Alan B

0

Expert Reply:

The replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System - Qty 1 # LC324269 needs to be torqued to 132 ft-lb and Lippert recommends using some Loctite Threadlocker 262 - High Strength - Up to 3/4" Nuts/Bolts - 0.20-Fl-Oz Tube Item # LT37420 to prevent the bolt from loosening. You are correct with the placement of the washer and o-rings.

expert reply by: Kevin C

0

Answer 1

Thanks for the picture! I took a look at what we got for your 2018 Thor Palazzo Motorhome, and it appears you need the Replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System #LC324269. This replacement will replace the foot pad…

view full answer...

Answer 2

I suggest using a strap wrench to hold the cylinder side while tightening the installation hardware on the Replacement Foot Pad, #LC324269.

view full answer...

Answer 3

For your bike rack, I recommend the Lets Go Aero LED Light Kit for GearCage4 and BigBoss Railed Cargo Carriers #H01540. This will easily work with your factory trailer connector. If you don't have the separate 4 way connection, then you can…

view full answer...

Answer 4

The exact replacement foot plate for the Level Up system you have is not available as a replacement. But you could use #LC314667. The issue is that it uses a smaller bolt than the Level Up foot. So you would have to use a 1/2 inch bolt that will…

view full answer...

Answer 5

If the touch pad is showing "Retract Time out Return Levelers for service" all you need to do is hit, enter and retract at the same time. That will clear that code. I confirmed this with our contacts at Lippert.

view full answer...

Answer 6

If your 2021 Jayco Greyhawk Prestige has hydraulic Lippert Ground Control leveling system then yes the replacement feet part #LC324269 would be correct. I attached a picture of what the jack leg should look like.

view full answer...

Answer 7

The Replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System #LC324269 needs to be torqued to 132 ft-lb. Lippert also recommends using Loctite Threadlocker 262 #LT37420 to prevent the bolt from loosening.

view full answer...

Answer 8

The Replacement Foot Pad #LC324269 that you referenced uses (and includes) a threaded 7/16" bolt for mounting. The mounting hole itself is just about 1/2" in diameter.

view full answer...

Answer 9

I went ahead and reached out to Lippert, and they confirmed that you need automatic transmission fluid Dexron III or Mercon 5 fluid. This works with their hydraulic auto leveling system. With that being said, I do not recommend using the hydraulic…

view full answer...

Answer 10

Yes, you'd need to hold the inner jack leg while you remove the bolt from the bottom when replacing the Replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System part #LC324269. In order to hold the inner jack leg, I recommend…

view full answer...

Answer 11

I understand your concern. I called Lippert to verify that the 132 Ft-lb of torque and use of Locktite is still valid. They said that was the requirement and there were no alternative instructions. The assumption is that this is the method they used…

view full answer...

Answer 12

Without knowing exactly which awning assembly you have-either 63" or 69"-there could be a number of parts that you might need. You can get just the pitch arm assembly with the Replacement Pitch Arm Assembly for Solera 69" Standard Flat…

view full answer...

Installing A Replacement Foot Pad For Lippert Hydraulic Ground Control Level System

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching