Dexter Predator DX2 Trailer Brake Controller - 1 to 2 Axles - Proportional
Replacement Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controller 12" Long
Part Numbers: 58-8,20127
Retail:$240.60
Our Price: $178.75
You Save: $61.85
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Dexter Predator DX2 Trailer Brake Controller - 1 to 2 Axles - Proportional
part number: 58-8
This proportional brake controller keeps it simple with intuitive controls that are easy to use. Includes a large digital LED display, fingertip gain control, a slide-bar manual override, and built-in safety features.
Features:
- Brake controller activates your trailer brakes in proportion to your vehicle's braking action
- Automatically adjusts trailer's braking based on deceleration of tow vehicle
- Large digital LED display shows your controller settings and monitors voltage output
- Simple, intuitive controls keep your settings in easy reach
- Adjustable gain setting determines the amount of braking output sent to the trailer's brakes
- Built-in, slide-bar manual override activates trailer brakes to control sway in emergency situations
- Deceleration sensor lever lets you adjust initial braking power and aggressiveness for smooth, safe braking
- Built-in safeguards protect your vehicle and trailer
- Current limiter protects vehicle from shorts in the trailer wiring
- Hazard flasher immunity prevents pulsing of the brakes when flashers are activated
- Quick and easy mounting with included bracket and hardware
- 90 To -35 degree mounting range - must be horizontally level
- Pigtail harness hardwires into your vehicle
- Made in the USA
Specs:
- Application: trailers with up to 2 axles (4 brake assemblies)
- Compatible with electric brakes only
- Dimensions: 6-1/2" long x 3" wide x 1-5/8" tall
- Mounting angle: -35 degrees to 90 degrees vertically
- 7-Year limited warranty
Proportional Braking
The Dexter Predator DX2 brake controller comes equipped with proportional braking to give you the best towing experience. Proportional braking means that your trailer brakes mimic your tow vehicle's brakes. If you slam on the brakes in your vehicle, your trailer brakes will activate with the same intensity; if you brake lightly, your trailer brakes lightly too. The trailer's braking is in proportion to your vehicle's braking. This saves wear and tear on the tires and the brakes on both your vehicle and trailer.
The Predator DX2 uses an internal 3-axis accelerometer to sense how your vehicle is braking so it can send the right amount of braking power to your trailer. It measures the inertia of your tow vehicle and activates the trailer's brakes to slow at the same rate. The result is uniform braking across your towing setup. No push-pull action - just smooth, proportional braking every time.
Large Digital LED Display
The Dexter Predator DX2 features a large LED display that's easy to see so you can check on your current braking output setting with a glance. This display is designed to keep it simple and not overload you with information. The display will also show you the voltage to confirm that the trailer brakes are receiving power.
Braking Output
During the initial setup process, use the thumbwheel on the front of the brake controller to adjust the braking output. The output control lets you set the maximum amount of power that will be applied to your trailer's brakes. Typically, the output is only readjusted when you experience changing road conditions or if the weight of your trailer changes. The power output control on this brake controller lets you set the maximum amount of power that will be applied to your trailer's brakes. Typically, the power output is only readjusted if you switch from a heavy, loaded trailer to a much lighter, empty trailer - or vice versa.
During the initial setup process, you can use the thumbwheel to adjust the power output. To get more power to your brakes, increase the power level. To decrease the power output, lower the power level.
Sensitivity Adjustment with Deceleration Sensor Lever
Once you have the overall power set, you can fine-tune the power output by adjusting the sensitivity of the internal sensor. This controls the aggressiveness of your trailer's braking, meaning how quickly the brakes reach the maximum braking level. You can adjust this when you're towing heavy loads and you need more umph to bring your trailer to a stop. Your tow vehicle doesn't need that much power to brake in time, but your heavy trailer does. Boost gets the braking power to your trailer brakes faster and with more intensity so that it doesn't push your tow vehicle forward. To increase the sensitivity for towing heavier loads, move the lever away from you. For a lighter load, move the lever toward you.
Slide-Bar Manual Override
The Dexter Predator DX2 comes with a built-in manual override slide-bar in easy reach, great for stopping sway or controlling your trailer's momentum in emergencies. To engage the manual override, just push the slide-bar to the left. This will activate the trailer's brakes and brake lights without you having to apply the brakes on your tow vehicle, perfect for limiting trailer movement while you're cruising.
You can also engage the manual override to help you move a sliding 5th-wheel hitch closer to your truck's tailgate for tight maneuvering during slow speed turns. Just apply the manual override to hold the trailer in place while slowly moving the tow vehicle forward.
Quick, Simple Installation
Because the controller operates with an internal inertia sensor, it must be mounted between -35 degrees and 90 degrees vertically. The Predator DX2 also needs to be horizontally level and parallel with the direction of travel to function properly. During initial installation, the deceleration sensor lever must be positioned straight up and down. After mounting the Predator DX2 using the included bracket, hardwire the controller directly into your vehicle.
Installation Accessories
See etrailer.com's exclusive 7- and 4-way brake-control installation kit (ETBC7 - sold separately) if you don't already have a 7-way plug at the back of your vehicle
Note: One of the following will be required to ensure proper installation:
- 20-Amp circuit breaker (9506P - sold separately) for 2- to 4-brake applications
- 30-Amp circuit breaker (38630 - sold separately) for 6- to 8-brake applications
058-008-00 Dexter Predator DX2 Electric Brake Controller with Inertia Sensor - 1 to 2 Axles - Proportional
Replaces 58-8
Replacement Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controller 12" Long
part number: 20127
Tow Ready Replacement Plugin Harness for the Tekonsha P3, Voyager, Prodigy, and Primus Brake Controllers. Also works with Draw-Tite Intella-stop Xtreme, Intella-stop Ultra, Intella-stop Digital, and Activator III (5520) brake controllers.
- Wire lead length: 12"
- Wire functions:
- Blue: trailer brakes
- White: vehicle battery negative terminal
- Black: vehicle battery positive terminal
- Red: cold side of stoplight switch
8506920 Replacement Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controller 12" Long
Replaces 20127
California residents: click here
Customer Satisfaction Score:
94% were satisfied with this product
6% of customers were not satisfied
- Wrong item was ordered
- Defective
- Too difficult to install
Customer Reviews
Dexter Predator DX2 Trailer Brake Controller - 1 to 2 Axles - Proportional - 58-8
Replacement Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controller 12" Long - 20127
Average Customer Rating: 4.8 out of 5 stars (736 Customer Reviews)
This proportional brake controller keeps it simple with intuitive controls that are easy to use. Includes a large digital LED display, fingertip gain control, a slide-bar manual override, and built-in safety features.by: Michael 02/18/2023
Exactly what I was looking for and needed ! It was delivered very quick . Actually I just ordered a complete wiring harness from you tonight . Your service and follow up is great
by: David11/05/2019
2007 Ford Ranger
Purchased a Teckonsha Voyager brake controller and the ETBC7 install kit.
The instruction an video were very clear and easy to follow. Installed on a 2007 Ford Ranger Sport. Tech support was also very helpful on the one question I did have.
David
11/8/2020
I have been completely satisfied with this item. It has operated as advertised an has had no problems.
by: Wayne12/20/2019
The drawtite hitch and trailer wiring harness fit great. Instructions were clear and concise. Installation was a breeze. I am ready to tow my little trailer now. As soon as I get the brake controller installed, I will be ready for my big trailer.
by: Chris C10/09/2016
If your truck comes with the tow haul package.... this item is literally plug and play. I had it wired up and all mounted inside of thirty minutes. It's literally 4 wires and the stock system wires are labeled along with the brake contoller. I haven't tested it yet but so far I am thoroughly impressed!
by: Easy install01/21/2021
Perfectly wired directly to existing wiring that I had for the previous brake controller I replaced with the, Draw Tite I Command. This will make it a lot easier should I choose to upgrade the unit in the future.
Fantastic customer service from Joshua as well.
by: Griff Morgan06/19/2022
Class iii Draw Tite trailer hitch:
This part was quick and easy to order and I received it sooner than expected. My mechanic said the installation was easily accomplished and looks great on my car. I would not hesitate to order from etrailer again!
Griff M.
6/21/2023
The product has worked well. I have had no problems with it.
by: Rudy04/20/2023
Purchased this as part of all parts required to convert 1996 Jayco over to electric brakes. Very happy with results. Surprised to see after winter in storage that the battery supply still shows full charge.
by: Bryce05/03/2022
Ram 2500
I installed the Curt gooseneck on my 1993 GMC 2 Wheel Dr. 2500 truck. All the components have tight tolerances. It took me eight hours. With a socket and the wrench. Laying on my back. I did have to cut the wheel well lip about 3/8 of an inch off because I could not get that front angle bar to slide in without hitting it, no way around it unless you lift the bed up and I wasn’t going to do that!!. You have to cut it.instructions do not state that. I’m very happy with the Hitch, it is definitely stout! I did have to make a notch on the outside brackets to go over my airbag bolt. I also had to remove the support bracket on the inside of the frame for the airbag and the crossmember for the spare tire to get the front angled bar in.
by: Douglas08/03/2023
As always, etrailer delivers. Part was on time and a perfect match for the brake controller. What you don't get from Amazon is the technical support on how to install or use the equipment purchased from etrailer. That's why I keep coming back!
by: Rancher01/07/2023
Finally a brake controller that does what I set it to, not what it’s little computer brain, designed by someone who has never pulled a trailer thinks it needs to do.
by: Tim 06/21/2020
These guys are great they had the installation kit it came with everything you need and even had a video for my specific vehicle to install the brake controller and wire in a 7 pin trailer plug
If you don’t have factory brake controller the etbc7 is an amazing kit they have comes with everything I mean everything
Tim
6/26/2021
Everything has been excellent e trail has the right products and they fit just like they say
by: Don 03/07/2021
My truck was stolen and wrecked. I was able to retrieve the Tekonsha Brake controller from under the Dash board before it was hauled to the salvage yard, but not the wire harness. I was ale to order a replacement harness from eTrailer and reinstall the controller in my new truck. I had no problems at all. Thank you eTrailer for the great support.
Don
3/9/2022
Still works perfectly after one year. Actually, I been using this Controller for well over a year. I just reinstalled it in my new truck a year ago.
by: Charles 09/25/2022
Chevrolet
Wiring harness I used to connect into the trailer brake control circuit. Requires pulling some inside trim in the drivers footwell area to access my 2022 Chevy Colorado's wires. Follow the intructions or better yet go onto YouTube for video on what goes where.
by: Chad07/13/2021
Works as intended, but the plug on the back of the controller is a loose connection. Sometimes I would go to brake and find that I had no trailer brakes because the controller lost power. After a wiggle it would start to work again. I was able to shave the Molex plug a bit and now I don't have any problems with it.
Sierra K.
7/19/2021
Thank you for your review. I have not heard of that problem. I would have used some electrical tape.
by: Bill08/13/2020
The service you receive from etrailer is top notch. This brake controller has worked very well. I actually swap it between two of our vehicles. Just unplug it from one and plug it into the other.
Bill D.
8/15/2021
Very well. The service etrailer provides is the highest Ive ever experienced. They are just super to work with. Ive used them time & time again. I recommend them to everyone looking for anything they carry.
by: Michael 09/22/2022
I installed this controller in my 1982 Chevy K20 pickup.
It works perfectly! Etrailer exceeded my expectations with their level of customer service from the time the order was placed to the products arrival at my home. Truly 5-star service!
The video tutorials are straight forward and very helpful.
The universal installation kit literally had everything needed to complete the job.
Side note:
I would have liked to see the (2) 10ga wires in the insulation to be black and blue, not black and white, no biggie, black on black and white on blue.
Thanks again!
by: Steve03/10/2024
1976 Chevrolet Blazer
Great selection and servive
by: Shad11/01/2022
Works great. FYI YOU HAVE TO RUN A BRAKE WIRE FROM THE CONTROLLER TO YOUR LIGHT PLUG . For it to work properly.
by: Mile03/19/2024
Quality plug and what i needed for my F-53 chassis.
by: Bernard05/16/2023
The controller is on 24/ 7.I wish it turned on with the truck but this is more of a criticism of the truck not the controller I added a toggle switch so I can turn it off when I will not be using the trailer for a long spell.
by: Richard12/28/2022
was difficult to find a good mounting location away from leg room
by: Beck05/28/2022
One year later I'm extremely pleased with this purchase. I often chuckle when I see stock hitches and the whole thing is visible while mine is neatly tucked under with everything hidden except for the 2" receiver. 10/10 have recommended etrailer on many occasions to friends and family for their service and know-how. Since installing my hitch I towed a pop up camper 1500+kms and do frequent trips to the dump or my local dirt and gravel yard for supplies. Love it!
by: Steven05/03/2022
2008 Honda Pilot
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat, Item # ETBC7
I installed this 7-pin plug kit on my 2008 Jeep JKU to add power and trailer brake control.
I also purchased :
Draw-Tite I-Command Trailer Brake Controller Item # 5535
and
Curt No-Drill Bracket Item # C57202
along with a little extra wire, just in case.
The kit quality was great. It shipped with everything I needed, sans the controller and bracket above. I used a cordless drill, a quarter inch drive socket set, screwdrivers, wire cutter/crimper, pliers, black electrical tape, half inch loom (plastic flexible conduit) and quite a few extra zip-ties I had laying around. I needed the Curt bracket to mount the 7-pin plug farther away from the muffler that runs parallel to the bumper in Wranglers.
I first ran the grey jacketed wire from the rear bumper all the way to the engine compartment. This was the hard part for me since I'm old and a little more round than I'd like. I didn't need to raise the jeep since it already has a 2 1/2 inch lift. I zip-tied the jacketed wire to the frame and brake lines until I found a spot in the frame I could run it through. I ran it out of the frame at the rear of the left front wheel well and up into the engine compartment. There is a (very handy) rubber plug in the firewall just to the left (outboard) side of the brake vacuum booster. I made a small slit in the rubber plug. I removed the outer jacket from the wire at that spot and fed the white (future brake controller wire) into the cabin of the jeep. I ran the black wire, in a wire loom/conduit across the top of the firewall to the battery. I had enough extra wire to run the brake controller power and ground wire from the battery, across the top of the firewall in the same conduit, and into the cabin through the same rubber plug/grommet. I drilled small pilot holes to mount the two circuit breakers. I then connected the wires at the 7-pin plug at the rear bumper. I again made a pilot hole and then mounted the ground wire with the self-tapping screw provided in the kit.
Here I'd like to mention, I would have been happier with heat-shrink connectors. I could have gone to town and bought some, or I could have soldered the connections. Instead, I just used the provided connectors and a LOT of black tape. If I have any corrosion issues later I will replace the connectors provided in the kit.
I wired and mounted the brake controller. This would have been super easy if I could fit under the dash. I dislike using the little blue inline wire connectors (self stripping connectors) but it was a godsend when working one-handed under the dash. I mounted the controller bracket and covered most of the exposed wiring with black tape for aesthetics.
If I was 20 or 30 years younger, I would have had this whole kit installed in about 1 1/2 hours. I am very happy with the quality of the materials. Many others have already noted the bracket is not quite perfect where it is designed for the four wire plug to slip in. The four wire plug had moved slightly on my 20 minute drive to work and would likely have fallen out if I went much further. I may put a wrap of electrical tape around the plug to tighten up the fit. Otherwise I will see if a zip-tie or a drop of superglue will hold the four wire plug in place. I was a wee bit skeptical about the sturdiness of the no-drill bracket as it's held in place by what looks like a hose clamp. I am happy to report, the clamp is heavy duty and well made. The no-drill bracket with the 7-pin and 4-pin receptacles are very sturdy and secure. The instructional videos on etrailer's website made the job easy to understand.
If I had this job to do over again, I would definitely use the same products from etrailer.
by: Bob J.09/07/2016
I am very satisfied with the Dexter Axle Predator Electric Brake controller. I purchased the Dexter brake controller to be compatible with Dexter car trailer axles on a 16 foot car hauler. The braking unit is very useful when towing in very steep and winding mountain terrain. I feel that the braking is a necessary safety item when towing in a hilly or mountainous environment and the Dexter Predator brake controller provides the great control and driver peace of mind knowing that a heavy load can be managed. The unit installs very easily with the proper adapter.
by: Ken D.02/22/2022
Both the 2017 & 2018 Winnebago Forza class A motorhomes DO have in place (under dash) connections for trailer brake controllers, unlike as depicted on your website as needing an additional part (wiring and 4 prong plug), although it is somewhat difficult to find. Attached to the connection socket is an unwired plug (with blue "lips" in somewhat blurry photo). One could either cut and splice the 12" plug-in harness (#20127) into the vehicle connections, or as I did, use solderless socket connections. To determine what wires go where, use an ohmmeter. You will find two b+ wires (use either one) a ground connection, a brake signal wire(use DC voltmeter and press on brake pedal (engine on in diesel pusher) to get reading, and a to trailer wire (bottom left corner when two b+ and ground wire are on right side of socket).
25
736
Show More Reviews Ask the Experts about this Trailer Brake Controller
Do you have a question about this Trailer Brake Controller?
- 2017 Jeep Wrangler Unlimited Brake Controller Installation
- The Dexter Predator DX2 Trailer Brake Controller - 1 to 2 Axles - Proportional # 58-8 will have the red wire connect to the brown and white wire in your 2017 Jeep Wrangler Unlimited. I've attached a video of an installation of the Prodigy P3 # 90195 which will have that same red wire from the brake light switch. This installation uses heat shrink butt connectors # DW05745-5 along with wiring kit # 5506 to Factory 7-way.
view full answer... - Location of Brake Controller Connector on 2012 Ram Truck
- The connector you are looking for will be located taped to another larger wiring harness just to the right and above the emergency brake pedal, as shown in the photo I have edited for you.
You can confirm that this is the correct connector by testing it with a circuit tester like part # PTW2993. One pin should show a constant 12-volt power supply, another should show voltage only when the brake pedal is pressed.
Unfortunately, my contact at Tekonsha was not able to shed any light
view full answer... - Brake Controller for 1999 Chevy Tahoe Towing a 2006 Fleetwood Bayside Camper with Electric Brakes
- Since brake controllers are not vehicle-specific, you can use any of our brake controllers with your 1999 Chevy Tahoe and camper. The Dexter Axle Predator Electric Brake Controller, part # 58-8, is a great choice. It is inertia-activated, meaning you have a lot of mounting options for inside your Tahoe, has an LED display showing voltage output, and works with 1 or 2 axles.
If you don't already have a 4-way connector on the back of your vehicle, you will need the custom-fit Vehicle Wiring
view full answer... - Parts Needed to Install a Trailer Brake Controller on a 1987 Dodge Ram 350 Full Size Van
- The 1987 Dodge full size vans do not have wiring under the dash to wire in a brake controller. You will need to hardwire in the controller using an installation kit. There are different kits depending on whether or not the vehicle has a trailer connector or not.
If your van has a 4-Way trailer wiring harness, you will need to use the 4 and 7 way installation kit # ETBC7. It comes with the 7-Way, wiring, and accessories to wire in the brake controller. If you do not have any type of trailer
view full answer... - Troubleshooting No Truck Brake Lights When Manual Override Used on Dexter Predator Brake Controller
- According to the Dexter Predator # 58-8 Brake Controller installation instructions, if your truck lights are not illuminating properly with the manual override is activated, then you will need to check the red stoplight wiring connection. The brake controller red wire should be connected to the non-powered stop lamp switch wire on your 2008 GMC Sierra.
On your specific truck there should be a wiring bundle that is below the steering column, and is to the left of the brake pedal. This
view full answer... - Hazard Lights Locking Up Trailer Brakes and Activating Electric Brake Controller On RV
- If the red wire from your brake controller is tapped into a wire that has voltage when the hazard lights are activated then this situation will occur.
You will need to attach the red wire from the brake controller to a brake signal wire, under the dash at the brake pedal switch, that only has power when the brake pedal is pressed on your RV, so that when the hazards are on your trailer brakes do not lock up.
view full answer... - Installing Dexter Predator DX2 Brake Controller on 2008 GMC Envoy
- As long as your 2008 GMC Envoy is equipped with the factory 7-Way connector there will be blunt cut wires located inside the vehicle on the driver's side under the instrument panel to which your Dexter Predator DX2 Brake Controller # 58-8 can be directly wired. Based on my research there should be a red/black wire that connects to the black (12V power) wire on the controller, a white wire that connects to the white (ground) wire on the controller, a light blue/white wire that gets connected
view full answer... - Parts Needed To Tow a Towmaster Trailer with Electric Brakes with a Winnebago
- The Dexter Predator brake controller # 58-8 would be a good fit to power the trailer brakes on your Towmaster trailer. You would need to hard wire the brake controller to the Winnebago, connecting the wires coming from the back side of the brake controller as follows.
The brake controller wire functions are:
White: Ground, attached to a clean piece of unpainted metal.
Black: 12v lead, attached to the positive battery terminal on the Winnebago with a 40amp circuit breaker.
Blue:
view full answer... - Where Do the 4 Wires of a Brake Controller Go for Installation in Vehicle
- The four wires and their functions are:
White: Ground wire, connected to negative side of battery.
Blue: Electric brake wire, ran to the brake output circuit of your 7-way with 10 gauge wire like # 10-1-1 sold by the foot.
Black: 12v power wire, connected to the vehicle positive battery terminal with a 40amp circuit breaker, part # 9510.
Red: Stoplight switch circuit. This will get run to the wire on your stoplight pedal assembly that sees voltage only when the brakes are applied.
view full answer... - Trailer Brake Controller for a 2008 Saab 9-7X with Factory 7-Way Trailer Connector
- The 24 pin receptacle you are seeing sounds like the OBD2 port and would not be used for a brake controller. You will need to utilize the owners manual or a Saab technician to locate the wires and to determine the functions of those wires. Identifying the wire functions is critical because a brake controller has to be hardwired in since there is no plug and play option available.
The wires on a brake controller are as follows:
white is ground
black is 12 volt power in
blue is output
view full answer... - Can a Trailer with Electric Brakes be Converted to Surge Hydraulic Brakes
- You can convert your trailer from electric brakes to hydraulic surge brakes, but it will require new brake assemblies, a new coupler and brake lines. To see all that is needed check out the FAQ article I attached to the right.
view full answer... - Can the Dexter # 58-8 Predator DX2 Brake Controller Be Installed Vertically
- According to Dexter, the # 58-8 Predator DX2 needs to be mounted in the direction of travel, level on a side to side plane. If mounted on vertical plane as you mention, the brake controller would not function.
If the vehicle design somehow limits the installation options, and you have no other option than to mount a brake controller vertically, you can use a time delayed brake controller like the # 5504 Draw-Tite Activator IV. Because the controller is solid state, if can be mounted
view full answer... - Is the Dexter Predator DX2 Trailer Brake Controller Compatible with a Triple Axle Trailer
- The Dexter Predator DX2 Trailer Brake Controller # 58-8 is only rated for up to 2 axles. If your trailer has 3 axles then I recommend the Tekonsha Primus IQ # TK90160 which is a proven proportional brake controller at a cost-effective price. This also uses the same wiring configuration as the DX2 so if you are splicing it in to your tow vehicle you will use the following:
Blue - 7-Way Output to Trailer
Black - 12V Power
White - Ground
Red - COLD Side of Stop Light Switch (only gets
view full answer... - How to Install a Brake Controller in a 1996 Dodge Ram
- If your 1996 Dodge Ram has the factory 7-way connector at the rear of the vehicle, then all of the wires for the brake controller have been run. You will just need a brake controller wiring adapter. I recommend using part # 3020-P and cutting off the black plug. This adapter plugs into the brake controller plug under the dash, to the left of the steering column taped to another harness near the emergency brake pedal. The four pigtail wires on the other end will be butt-connected to the
view full answer... - How to Wire a Dexter Axle Predator Brake Controller 58-8 on a 2001 GMC Sierra
- The light blue wire mentioned in the video of the # HM40975-11998 7 and 4-pole trailer connector being installed on a 2002 Silverado is for a camper shell brake light, and is not for use with an electric brake controller.
The electric brake wire on your 2001 GMC Sierra is run from the port below the dash into the engine compartment, but it does not continue back to the rear wiring bundle. You will need to finish the connection by running a wire from the 7-Way in the rear of the truck
view full answer... - How to Wire Dexter DX2 Brake Controller on 2013 Chevrolet Silverado
- The red wire from your Dexter DX2 brake controller # 58-8 needs to be wired to the cold side of the stop light switch, which on your 2013 Chevy Silverado corresponds to a light blue wire with a white stripe. This wire should ONLY be hot when the brake pedal is applied.
The rest of the wires actually match up with the same color wires on your truck as follows:
Dark blue on brake controller - To dark blue on vehicle
White on brake controller - To white on vehicle
Black on brake controller
view full answer... - Wiring a Brake Controller on 2010 Chevy Silverado
- You are correct, the tow package wiring in your Silverado does not match up color for color with the controller.
The red/black tow package wire will connect to the black wire on the controller. The dark blue tow package wire connects to the blue wire on the controller, the light blue tow package wire connects to the red controller wire, and the white tow package wire connects to the white wire on the controller. The orange tow package wire is for an illumination circuit and is NOT needed.
view full answer... - Installing a Brake Controller on a 2016 Chrysler Town and Country Van
- The 2016 Chrysler Town and Country did not come with a factory installed tow package and a 7-way trailer connector. You will have to hardwire in a 7-way and the all the wiring so you can install your controller. None of the wiring is pre-installed on this model vehicle.
The first thing you will need to do is wire in a 4-way flat trailer plug if you have not already done so. You will need a wiring harness, I recommend the Curt T-One harness, # C56331. This harness is custom-fit to your
view full answer... - Can the Predator DX2 Brake Controller Work on a Trailer with 6 Brake Assemblies
- I have a solution for you, but the Dexter Axle Predator Electric Brake Controller # 58-8 that you referenced can only be used on up to 4 brake assemblies.
Instead you would want the Prodigy P2 Brake Controller part # 90885. This controller can be used on up to 8 brake assemblies and would work great for you. This is our best selling controller because of how easy it is to set up and how well it works.
view full answer... - Parts Needed to Flat Tow a 2005 Cadillac SRX or 2007 Ford Edge Behind a Motor Home
- In order to determine if your vehicles can be flat towed and if there are any special requirements (such as a specific transmission or engine) you will want to consult your vehicle owner's manuals.
To flat tow either vehicle you will need 5 main components: base plates, tow bar, safety cables, lighting, and a supplemental braking system.
Base plates for the Cadillac SRX: # 3125-3.
Base plates for the Ford Edge: # 4408-1.
Compatible tow bar for either vehicle: Falcon # RM-520.
Safety
view full answer... - Parts Needed to Swap Tekonsha P3 Into 1995 Chevy K-Series Pickup
- In order to use a Tekonsha Prodigy P3 # 90195 in a 1995 K2500 pickup, you can use the Replacement Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controller 12" Long # 20127 to hardwire the controller in. To mount the controller you'll want to use the Replacement Mounting Bracket Kit for Tekonsha Prodigy P3 Trailer Brake Controller # TK5906. This would give you the parts you'll need to use it in both your 4Runner and the K Series.
view full answer... - Wiring Harness Plug-In To Brake Controller On 2008 Honda Ridgeline
- In the video that you linked, the part you are looking for is now the Replacement Brake Control Plug-In Harness Item # 20127. This part is specified to work with Tekonsha and Draw-Tite brake controllers. It will allow you to wire to the ETBC7 for safe towing.
I have added some review and installation videos below to further show the harness.
Tekonsha PowerTrac Electronic Brake Controller - 1 to 2 Axles - Time Delayed - Item # 39523 is the brake controller that was used with the
view full answer... - Can Brake Controller be Installed in 2020 Subaru Outback & Recommended Basic Controller
- You can install a brake controller on your 2020 Subaru Outback, and there is indeed a stop light switch on the vehicle. I have added a photo from a video of a brake controller install we did on a '20 Outback that shows the location of the stop light switch, which will be up under the brake pedal. I have linked the video for you below, and it talks about the stop light switch at about the 16:05 mark.
In regards to a basic brake controller, I think the best option is a time-delayed controller
view full answer... - Which Brake Switch Wire is Used When Installing Brake Controller on 2008 Dodge Ram 1500
- A brake controller has four wires exiting the rear of the controller, they attach as follows: the red wire attaches to the brake stoplight switch located at the top of the brake pedal. The color of the correct wire on the brake switch is usually a white wire with a tan stripe, but it could vary so it is best to find the correct wire you will need by testing the wires for function. The stoplight switch can have several wires exiting it, you will need a circuit tester like Quickee Tester,
view full answer... - Troubleshooting Brake Controller Only Functioning with Override Lever
- If you have a circuit tester like the part # PTW2993 test the red wire of the brake controller for voltage when the brakes are applied. If there is voltage when you press the brakes then the brake controller is bad but if not then the issue is that you aren't getting a stoplight signal for the controller to allow the controller to know you are applying the brakes. Sometimes this issue is as simple as a blown third brake light fuse or just a bad connection to the vehicle wiring.
view full answer... - Recommended Value Brake Controller For 2017 Honda Ridgeline Without Tow Package
- We can for sure get your 2017 Honda Ridgeline set up with a brake controller, and there is one that I think meets your needs perfectly, which is from Tekonsha; it will also require a wiring adapter, which will depend on if your '17 Ridgeline has the factory tow package or not:
- Tekonsha BRAKE-EVN Trailer Brake Controller # TK63VR
- Brake Control Harness # 20127
The BRAKE-EVN is a really good value, as it gets the job done of giving you reliable braking without any unnecessary
view full answer... - Er Code on Draw-Tite Activator Brake Controller
- So the "Er" code on the Draw-Tite Activator IV Trailer Brake Controller indicates an internal problem, and the controller will need to be replaced. I recommend going with a higher quality unit from Tekonsha, the BRAKE-EVN:
- Tekonsha BRAKE-EVN Trailer Brake Controller # TK63VR
The # TK63VR is also a proportional controller, which is an upgrade over the time-delayed Activator because proportional controllers apply the brakes in your trailer with the same force as you apply the brakes
view full answer... - Brake Controller Pigtail Wiring Harness For Infiniti QX 80
- We do carry wiring pigtails for Tekonsha prodigy trailer Brake Controllers that will work on your 2014 Infiniti QX80. I have attached a link to a help article that explains installation of a brake controller.
If you are looking for just the pigtail that attaches to the controller I recommend the Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controller, part # 20127. This harness has 12 inch wire leads.
If you prefer a harness with longer wire leads, I recommend the
view full answer... - Installing a Brake Controller on 2013 Mazda CX-5 with 7-Way Installed
- Since you have a 7-Way you will only need a few more components to complete a brake controller install on your vehicle.
For a wiring kit to install the brake controller and the 7-way adapter you would want the Wiring Kit for 2 and 4 Brake Electric Brake Controllers # 5506. This will provide the power source and ground for the wiring for the brake controller. You will need to test the wires from the brake pedal switch of your vehicle to find a circuit that has voltage when the brakes
view full answer... - Brake Controller Recommendation for 2013 Ford Edge
- There is one other part you will need so you can install a brake controller to your 2013 Ford Edge, the Universal Installation Kit for Trailer Brake Controller # ETBC7.
This will give you the 7-way connector, circuit breakers and rest of the hardware needed to install a brake controller, and work with your '13 Edge's hitch like the Draw-Tite # 75992 and 4-Way Wiring Harness # 118515.
Once you have all of this installed the brake controller I recommend for your 2013 Ford Edge is the
view full answer... - Will Tekonsha Voyager Brake Controller Work on Truck With Air Brakes
- You can install the Tekonsha Voyager Trailer Brake Controller # 39510 in your 2000 Kenworth truck in the exact same manner as you would a standard passenger vehicle. Your truck has a brake light switch as you mentioned, so you will wire the Voyager in the same way, and you'll also need the Brake Control Harness # 20127.
I have added a link below to a video review for you to check out as well if you'd like of the Tekonsha Voyager Trailer Brake Controller # 39510.
view full answer... - Recommended Wiring Harness for 2018 Buick Enclave and Tekonsha Brake Controller
- For your Tekonsha Brake Controller, the custom wiring harness # 3026-P is not a confirmed fit for your 2018 model as it was for your 2011 model. At this time we don't have a confirmed fit from any of our manufacturers. It appears that Buick has changed their connector and the only fit at this time is hardwiring the brake controller. For that, you can use the Replacement Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controller 12" Long # 20127. I've attached a wiring
view full answer... - Troubleshooting Prodigy Trailer Brake Controller Causing Dash Light Errors
- Sounds like it could be the way your brake controller was installed. I would first check the connection of the red wire, this should be connected to the brake light switch wire that is only active (hot) when the brakes are pressed.
Since you have a 2008 this newer body style has been known to need to be hardwired when installing the brake controller to function properly. I have linked a step by step Help Article for you to look at.
I would also recommend to clean out any corrosion
view full answer... - Installing Tekonsha Brake Controller on 1992 Ford F-150
- To install a Tekonsha brake controller, such as the PowerTrac Time Delayed Brake Controller # 39523, you would want a wiring harness. The Tekonsha and Draw-Tite Brake Controller harness # 20127 is designed to work with Tekonsha brake controllers.
If you do not have a 4-way flat or a 7-way connector at the rear of your 1992 Ford F-150, you will want to install a wiring harness with a 4-way flat. I recommend the Tow Ready T-One Wiring Harness # 118316. This wiring harness will plug into
view full answer... - Parts Needed to Install a Brake Controller in a 2013 Ford Edge
- You will need to hardwire in a brake controller on your 2013 Ford Edge.
First you will need to convert the 4-way to a 7-way. For that you will need an Brake Controller Installation Kit # ETBC7. This comes with everything you will need to install a fully functional 7-way and brake controller in your vehicle. I attached installation instructions and an install video for this product for you to check out.
If you do not have a brake controller picked out yet check out the Prodigy P2
view full answer... - Installing Brake Controller on 2013 Dodge Grand Caravan with FactoryTow Package
- It sounds like your Grand Caravan is wired like the Jeep Grand Cherokee. I have confirmed this by speaking with my contact at Tekonsha. He tells me that the wire you located is indeed the brake control output circuit. This wire would be ran through the firewall and would connect to the blue wire on the brake controller.
To complete the installation, you will connect the white wire of the controller pigtail # 20127 to the negative battery terminal, the black controller wire to the positive
view full answer... - How to Find the Brake Switch Wire to Install a Brake Controller in a 2013 Ford Edge
- Traditionally (at least from 2004 to 2007) Ford has used a green wire on the brake switch to attach to the red wire on a brake controller. However, the only way to know for sure is to test the wires using a circuit tester like # PTW2993. Manufacturers can use any wire they want and if they run out of the normal color they use, they grab whatever is available to keep the assembly line moving.
To test the wire, use the circuit tester to probe the wires. You need the one that only shows
view full answer... - Does the Tow Package Wiring on a 2008 Chevy Colorado Match a Brake Controller Color for Color
- On the 2008 Chevy Colorado with a factory tow package, the wiring for a brake controller is located under the dash, to the left of the brake pedal. The wire bundle should have a white tag on it that also lists the functions of each wire. You will need to match the wires to the brake controller by function, not by color.
On the brake controller, white is ground, black is 12 volt power, blue goes out to the trailer connector, and red is in from the stop light circuit on the brake switch.
It
view full answer... - Where to Connect the Stoplight Wire on Brake Controller Pigtail
- To install the Tekonsha PowerTrac Brake Controller # 39523 in your 2006 Ford Escape, the red wire on your brake controller harness # 20127 needs to be connected to the stoplight switch under the dash in your vehicle.
There should be a wire for the stoplight switch on the back of the brake pedal. You will want to use a circuit tester, like # PTW2993, to find the wire that has signal only when the brake pedal is depressed. Testing the wires is the best way to be sure which wire is the
view full answer... - Installing a Trailer Brake Controller on a 2012 Dodge Caravan with Tow Package
- I spoke with a colleague who worked at Chrysler and he stated that they do not put the trailer hitch and 7-Way wiring on the Grand Caravan at the factory. That is something that the dealer installs. In any event here is what you will need to do. The brake controller will need to be hardwired into the vehicle.
The white wire on the brake controller will need to get connected directly to the negative terminal on the vehicle battery. The black wire will need to connect to a 30 amp circuit
view full answer...
Info for these parts were:
Expert Research:
Mike L
Expert Research:
Patrick B
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Jameson C
Expert Research:
John H
Video Edited:
Zack K
Video Edited:
Joshua S
Video Edited:
Mike H
Video Edited:
Dustin K
Video Edited:
Chris R
Test Fit:
Nicholas E
Test Fit:
Shane H
Test Fit:
David F
Test Fit:
Clayton O
Video by:
Andrew L
Video by:
Zach D
Video by:
Jonathan Y
Video by:
Jacob H
Updated by:
Wilson B
Updated by:
Alexander C
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Michael
2/19/2024
After 1 yr and many trips this product has more than exceeded my expectations. Would definitely recommend it to anyone