Yes the Draw Tite hitch part # 75742 will work great on your 2014 Honda CR-V to carry a bike rack. The hitch opening is basically going to be flush with the rear bumper edge so any bike rack that can fit a 2 inch hitch would fit and work great. view full answer...
Scissor jacks # UF48-979002 are meant to support weight but not lift it like you said so these jacks would not be the best option for your trailer.
Scissor jack # JSC-30-IND is listed as having the ability to raise, lower, and stabilize so you could use it with handle # JCH-1. Or use drill attachment # UF48-979005 to speed up the process. view full answer...
Let's begin with the hitch. I'd recommend the Curt # C11496.
You'll then need a trailer connector, but the one you need will depend on whether your Accord has the LED or incandescent taillights. If you have the LED lamps, use the Curt # C56173 wiring harness. If you have incandescent taillights, use Tow Ready # 118596.
Finally, you'll need a ball mount and a trailer ball. A trailer of the size you describe likely uses a 1-7/8 inch ball, like part # 19256. For a 2 inch ball, use part... view full answer...
If you feel the frame of the HitchMate TireStep, part # HE4040 may not fit in the opening on your 2004 Honda CR-V, we may have another option that will work for you.
I recommend the Wheel Step, part # PT68ZR. This has an adjustable rail that slips over and behind the tire on your CR-V, so it should not be a problem at all getting it to fit securely. This tire step has a 300 lb weight capacity. view full answer...
Since you have a roof rack on your 2008 Honda CR-V that includes crossbars that run from side to side I would recommend the Thule Stacker Kayak Carrier part # TH830. This kayak carrier can carry up to 4 kayaks and I confirmed with Thule that it will fit the factory crossbars of your 2008 Honda CR-V.
Check out the review video I attached for this carrier. view full answer...
Pop & Lock tailgate lock # PAL6100 does indeed fit your 2006 Honda Ridgeline. It will fit models with or without the factory backup camera.
I would say that either black, # PAL6100, or silver, # PAL6102, would look the best on your blue and gray Ridgeline. I have linked a couple of videos on these tailgate locks for you. The video I have linked would be pretty much identical to your 2006.
The lock prevents the handle from opening up far enough to release the latches holding the tailgate... view full answer...
I can make sure you get the correct wiring harness to install a trailer brake controller on your 2021 Honda Odyssey.
The best way to know if your 2021 Honda Odyssey has a 4-way trailer connector is to check the fuse panel in the rear driver side of your vehicle and check if the blue connector has a wiring harness attached to it or not. You can see the blue connector I mentioned at 2:52 of the Tekonsha # 118781 installation video I attached.
If you find that you do not have a 4-way harness... view full answer...
Let's begin with the hitch. Instead of the etrailer # e98855 that you'd looked at, I'd recommend going with the Curt # C64NR. The difference between the two is how visible they are once installed. The # e98855 will be fully visible, the # C64NR will have a concealed hitch crossbar with the only visible portion of the hitch being the receiver tube and the safety chain loops. This provides a much better appearance.
You've nailed it with the products needed to add a brake controller. You'll... view full answer...
Based on your dimensions you do need a 1 inch rise. Now that said Class I hitches you have to use only the recommended ball mount from the manufacturer would be the part # C45521. Due to the lower capacity of the Class I hitches using a longer or larger ball mount might cause excessive strain on the hitch.
For a hitch ball you'd want the # A-82 for a 2 inch ball or # A-80 for 1-7/8 inch hitch ball. view full answer...
At the widest point of the roller # CE29334 the bell measures 4 inches in diameter and at the narrowest portion in the center it measures 1-1/2 inches. view full answer...
Based on the excellent information you provided, the the total tongue weight (tongue weight of trailer plus cargo behind vehicle rear axle) will range between 450-550 lbs.
I will proceed on the assumption that your boat trailer has a straight, or pole tongue versus an A-frame as is typical for a boat trailer.
If your boat trailer uses a hydraulic surge coupler that compresses to actuate the trailer brakes, you will not be able to use a standard chain-suspended type W/D system like the... view full answer...
The Inno square bar roof rack part numbers # INB127, # INSUT, and # INK745 which fits your 2008 Honda Accord sedan would be the rack I recommend as it's a higher quality roof rack at a lower price than it's competition.
Then for a surf board carrier the Inno Surfboard Carrier part # INA744 would be a great solution as well. view full answer...
You can mount a 7-way under your 2019 Honda Odyssey with Draw Tite hitch # 76170 but you'd need to mount the 7-way bracket to the the lower rear bumper fascia. You'll want to start with a 4-way like part # 118753 and then convert to a 7-way with part # ETBC7 so you can install a brake controller like the Brake EVN # TK63VR.
The # ETBC7 comes with self tapping screws that you will run through the bracket into the lower fascia of your vehicle. view full answer...
Hello Tonya -
Thanks so much for letting me know that your 2017 Honda Civic is a 4-door sedan. Once I know if you have a center exhaust on your vehicle, I can go ahead and recommend some great 2-bike racks for you! view full answer...
The Malone Runway Bike Rack for 4 Bikes # MAL82VR will fit your two adult bikes and your two kids bikes with 20 inch and 24 inch wheels. This is a great rack for cross country road trips because the padded hooks on sliding arms hold bikes securely by the frame. If you have an unconventional frame or really small children's bikes, you will have to purchase a Malone Bike Adapter Bar for Women's, Children's, and Alternative Frame Bikes # MAL82VR. Also, the 9 inches from the center of the hitch... view full answer...
The first thing you will need for wiring your 2018 Honda Odyssey EX-L is the 4-pole harness. I recommend the Curt T-Connector, part # C56382. It has a relatively easy installation: just remove a few pieces of the rear trim panel and plug into the controller panel on the driver side. It also features a power converter which prevents overloading your vehicle's electrical system. I've included a video installation of this harness on a 2018 Odyssey.
The Curt Echo, part # C51180, helps with... view full answer...
For your 2019 Honda Odyssey you will need the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56382 which is confirmed to fit your vehicle and will give you the 4-way connector needed to tow a trailer.
This will pair up perfectly with the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # C13370.
To complete your towing setup you will also need a ball mount, hitch ball, and hitch pin and clip which can all be found in the etrailer Ball Mount Kit... view full answer...
For your 2012 Honda CR-V, there are two different trailer hitch receiver sizes, so a couple different popular options due to that.
For a 1-1/4 inch hitch receiver, the most popular is the 17x46 Curt Cargo Carrier for 1-1/4" Hitches lbs # C18145. This carrier has a straight shank for greater ground clearance, but it does not have a folding feature. The sides and the metal floor provide many attachment points for tie down straps like # EM04418 or the Cargo Net 36" x 48" # CS54FR. I recommend... view full answer...
Sounds like you may be interested in the part # D210. This will fit your 2 inch hitch and gives you a ball mount platform down below and a hitch opening above for your bike rack.
However, if you do not yet have a hitch yet, we have great news. We have the EcoHitch Hidden Trailer Hitch Receiver # 306-X7322 that has a 2" opening and a 300-pound tongue weight capacity. With this hitch, you could use the Thule Hitching Post Pro 4-bike rack # TH934XTR. I attached a video of these products... view full answer...
Yes, the Thule T2 Pro # TH83JV would fit and work great in the Draw Tite Hitch part # 75270 which is a confirmed fit for your 2014 Honda Odyssey.
I attached a review video that shows this rack. view full answer...
Go To Results