I attached a link to this page that has all of the ceiling garnishes we offer for RV roof vents and on that page you can select the brand of vent that you have and see what you'd need. We have Fan-Tastic, Maxxair, and Ventline in various sizes. view full answer...
The SportRack Pop-Up Camper Roof Rack part # SR1020 can be installed one of two way, via drilling into the roof or via integrated tracks (if present). It comes with the hardware needed for either installation. If you have the integrated tracks then the crossbars get secured to this using a spacer block and bolt which you can see in the photo below. view full answer...
Typically it's not going to matter since the bolts are just used to hold the valve body together, so the bolts holding your current waste valve together won't matter.
If you waned to use the LaSalle Bristol Cable-Actuated RV Waste Valve for Black Water Tank - Spigot to Hub - 48" Cable # 34466N4AB48GMA you'd just want to cut off your old waste valve and slide the LaSalle on; you'd want to secure it with some ABS Solvent # 3447530889, but going this direction it wouldn't matter what your... view full answer...
Great question. Almost all landing gear includes both bolting and welding. The brackets are welded to the trailer and then the legs have weld stops where the brackets fit and are bolted into place. Most landing gear is fairly similar in the weld stop locations, so new legs don't normally require replacing the brackets however there are some that require cutting off the old brackets and welding new ones in place.
For instance the Lippert Electric Landing Gear Set - Weld On - 37" Lift... view full answer...
The Replacement Fan Blade # BVC0466 and Replacement 12V DC Motor # BVD0218-00 will vent air out of your bathroom once it is installed on your Ventline V2399 unit. I have attached a picture of how this is installed for you to reference.
If you are wanting to use a vent that has the option to push air out or pull it in then I recommend using the Fan-Tastic Vent Roof Vent # FV801250 which operates via 12V, has the reversible function, and uses a manual knob to lift the cover. A review video... view full answer...
You will continue to use your awning's current arms when using the conversion kit:
- Solera Manual Pull Style to Power Awning Conversion Kit # LC329250 view full answer...
The RF controller of your Blue Ox Patriot Radio Frequency, Portable Braking System # BLU37TR doesn't have an internal battery and requires a 12v outlet for power. If you've already checked the fuse in the power cord and it still isn't getting power then I recommend checking that the fuse for the outlet itself didn't blow. You can try plugging the RF controller into a different vehicle's 12v outlet to see if it powers on and syncs to the system. If not then you may need to reach out to Blue... view full answer...
If the bump stops on your 2006 Fleetwood Bounder Class A Motorhome are going to interfere with the bags, or are directly in the spots where you're going to be mounting your Firestone Ride-Rite # F2070, they can be removed. With that being said, if they're not going to interfere with installation, you can leave them there to act as a fail-safe in the event that a bag were to rupture or some other type of freak malfunction (this is unlikely, but if they're not hurting anything you don't need... view full answer...
Yes, wiper blade # CP77261 does include the saddle and the hook so they can be installed either way without purchasing anything additional. view full answer...
I did some research on the ECC because I hadn't really heard of it before and I was able to find out that the ECC is strictly designed for use with 30A services according to the owner's manual. So, upgrading to 50A would effectively get rid of the ECC as it wouldn't be compatible.
With that being said, the Progressive Dynamics 4500 Series RV Converter w/ Charge Wizard and AC/DC Distribution Panel # PD4560K18LS8 would be a nice upgrade providing a 60A converter output.
This converter charger... view full answer...
You can trace the connectors you have on your fan assembly to determine where they terminate in order to install the new switch # FVK1031-05. Why your old switch had only 2 of them connected I can't say unless it did not have all the functions that this switch controls.
If looking at the back of the switch the single terminal on the left next to the spring is the power terminal. On the right side the upper terminal goes to the circuit board. And the lower right terminal goes to the fan... view full answer...
While it is typically used as a bolt on jack the ARK Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels part # ORJW750BD can be used as a weld on jack.
The bracket that is used to mount it is a standard steel. You will have to clean off the finish on it of course but touch it up afterwards and you'll be in good shape. view full answer...
Yes, the Swagman XTC-2 2-Bike Platform Rack part # S64670 is rated for use on a motorhome so it can be used on your Fleetwood Southwind Class A Motorhome. It does not have a pivot point on the shank which is what allows it to be used as such. It also has a threaded hitch pin which will help to stabilize the rack and bikes while in motion.
In order to lock the bike rack to your motorhome you will want to use the Locking Anti-Rattle Threaded Hitch Pin part # S64029. In order to lock both... view full answer...
The Lippert Kwikee 32 Series Electric Step - 2 Steps # LC372261 is the replacement step for your 903206001 on your 2003 Discovery. They should easily install without modifications needed. Due to the age of your steps and how much they've been used it would be pretty safe to assume they are just worn out. view full answer...
I think I found some information that'll help you install a brake controller, like the Prodigy P2 # 90885, but we don't carry a direct plug-in adapter for that connector you found.
From my research it is the correct connector so you've found the correct wires. You need to cut off the plug you found and test each wire for function to make sure you know which is which and then hardwire them to the controller. Use a circuit tester like # PTW2992 to test the connector you found. The wire... view full answer...
The Solera Manual Pull Style to Power Awning Conversion Kit # LC329250 is only compatible with Solera awnings, so it will not work with your Dometic awning. The conversion kits we carry for Dometic awnings are kits like the Solera 12V Power RV Awning Conversion Kit # LC434724, but these already have the arms attached.
We do not carry a kit like the # LC329250 for Dometic awnings, so I would not know exactly how they operate/install. view full answer...
I checked out pictures of the Starcraft ARone travel trailer I found online and it appears to have a 4 inch rear bumper like what the Swagman bike rack # S80600 was designed to fit so this would work well for you. view full answer...
The bolt pattern that is on the bottom of the Kwikee 32 Series Steps part # LC3722616 that you referenced is 22 inch by 8 inch but there are several bolt holes on the plate which might be why you are getting a slightly different measurement. view full answer...
The etrailer eDream Supreme RV Mattress # e77FR does have a good amount of flexibility. After all, they do ship rolled and compressed, so we know they can take quite a bit of "bending" and return to their original shape. It is not uncommon for these mattresses to be used in slide outs similar to yours.
That being said, the eDream Supreme mattress is not designed to be folded or bent repeatedly. So while it may bend when you retract the slide, the concern is that repeating this process... view full answer...
There is an adapter for your 2018 Fleetwood Discovery LXE 40D, it is item # 20127. This adapter will plug directly into your Tekonsha Prodigy P3 proportional brake controller item # 90195. However, this is not a plug in adapter that goes directly into your RV like you had in your Fleedwood Bounder. You will have to splice into your vehicles wiring to connect your brake controller. view full answer...