Most X3 models were equipped with the roof rails, so I initially thought you might be out of luck, but after searching around I found that Yakima offers a JetStream roof rack that would work perfectly on the bare roof of your 2013 BMW X3.
To assemble the rack, you'll need the following parts:
• 50 Inch JetStream crossbars in black as # Y00425
• BaseLine Tower Feet, part # Y28TR
• Front Fit Clip # Y06123
• Rear Fit Clip # Y06127 view full answer...
In order to install a brake controller on your BMW X5, you really just need the brake controller, since you've already got a factory 7 way plug. The caveat here is that your BMW does not have a plug in adapter available to install a brake controller, so installation of a brake controller would require hardwiring into the vehicle's wiring.
If you've already got a brake controller, you will need to look under the dash to find the 12v power from the battery, the brake control wire from the... view full answer...
It's most likely that you've got the BMW roof rack made by Thule, so you can use the Replacement Key for Thule Racks and Carriers - N019 # THKEYN019. view full answer...
I do have a solution for you, however Glo-Brite is no longer in business and subsequently their parts are no longer available, unfortunately.
Instead, what you can use instead is the Optronics Clearance or Side Marker Trailer Light - Incandescent # MC68AB.
This light measures 3-1/2" long, 1-2/8" wide, 1" thick, and is made from a durable ABS plastic.
Additionally, we do also have the same light available with a red lens # MC68RB if you ever should need it. Attached are a couple of... view full answer...
The Tekonsha Plug-In Wiring Adapter # TK29FR is what you'd use if your 2017 BMW X5 has the factory 7-Way connector at the back. Since you're using the T-One Vehicle Wiring Harness # TK47FR that tees in behind the tail lights on your vehicle you need to use the Universal Wiring Kit # ETBC7 instead. This kit comes with all of the wiring and connections you need for a fully-functioning 7-way as well as what you need to get a brake controller up and running.
Please note that it might be difficult... view full answer...
On the Curt Trailer Hitch Receiver # 13077 for your 2018 BMW X5 there is no requirement for the Curt Cam Buckle Stabilizing Strap for Hitch-Mounted Accessories # 18050. The strap is recommended for use with bike racks and other hitch-mounted accessories to avoid putting too much strain on your trailer hitch. Some Class I and Class II 1-1/4" hitches may require that you use a stabilizing strap to ensure that the hitch does not experience excessive torque while transporting your gear but... view full answer...
To add trailer wiring to your 2010 BMW X6 I recommend using the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector # C59236, which has a powered converter and comes with quick splice hardware to allow you to complete the installation.
If you also need a ball mount, hitch ball and hitch pin I recommend using the etrailer 2-3/4" Rise or 4" Drop Ball Mount Kit - 7,500 lbs # EBMK4 since it gives you all of the parts you should need to tow some different trailers. The ball... view full answer...
First you will need the Stealth Hitches Hidden Trailer Hitch Receiver w/ Towing Kit # SH93VR for your 2019 BMW 540i. This will include a 4-way flat for your tail light functions.
If your boat/trailer has electric or electric over hydraulic brakes, you will be able to connect the 4-way to the Adapter # A10-6034VP. Combining this with the Wiring Kit # 5506 and Brake Controller # RED52VR will allow you to control the trailer brakes along with adding a charge line for the trailer.
If your... view full answer...
For a roof rack that will fit your 2013 BMW X3 with the side rails that run front to back you can use a Thule rack using the following parts:
47 inch SquareBars # TH712200 or WingBar # TH711220
Thule feet # TH710601
Fit kit # TH186007
This rack has a 165 pound capacity. But check the X3 owners manual to determine the capacity of the roof and if lower go by the lower capacity. You can then use the Stacker, # TH830. It does not have a capacity because it will be holding up a kayak placed... view full answer...
The # SH64MR Stealth Hitch you'd looked at is a fit for your 2020 BMW X5 if it's an M Performance model. If you have the M Sport model, you'd want to use # SH89VR instead. The receiver included with either hitch is designed for carrying hitch mounted accessories only, and isn't designed to tow a trailer.
To tow a trailer, you'll need the # SH58VR towing kit which includes the ball mount and the trailer wiring harness assembly. The towing kit is compatible with all models of the 2020 BMW... view full answer...
Both hitches fit certain models of the 2018 BMW X5.
The EcoHitch # EH44FR will fit 2018 BMW X5 models, with the exception of M performance models (will fit M sport model) that have a rear back up sensor. The EcoHitch # 306-X7265 fits 2018 X5 models without the backup sensors, except M performance models.
The Stealth Hitch # SH79VR hitch you'd looked at fits all models except the M performance. For the M performance, you'd use # SH56VR. Both hitch include the receiver that's meant to... view full answer...
When installing The Stealth Hitch # SH89VR onto your 2023 BMW X5 there is no type of fascia or bumper trimming needed in order to install it. The bumper and fascia will remain intact, but there is a small piece that is underneath your vehicle that you will need to trim. The rock/gravel guard that is located underneath your BMW will need a portion of it trimmed in order to install the hitch. I will attach a picture below with a red arrow pointing to what needs to be trimmed. Ignore the yellow... view full answer...
At this time there is not an aftermarket brake controller wiring harness available for the 2004 BMW X5 3.0l. If your vehicle has factory original 7-Way RV tow package wiring you will have to contact the dealer to see if there is a brake controller wiring port and mating plug for installation of a brake controller on your vehicle.
If your vehicle is not set up with factory 7-Way RV tow package wiring, you will need the, # 119250KIT, Circuit Protected 4-Way wiring harness, if you do not... view full answer...
Great news, I can help you figure out what you will need for your LED trailer lights to work in combination with your 2011 BMW X5 LED lights.
If you have a factory 7-way installed on your vehicle from the manufacturer, then you may need one of the two adapters # C57003 or # 20142 you referenced. Both would work and complete the same function, the Tow Ready # 20142 is a popular option among our customers.
If you happen to have an aftermarket one like our # 119250KIT that has a power wire... view full answer...
Both of those parts are members of the Hollywood Racks SportRider family of bike racks, so you can use the Fat Bike Adapter Kit for Hollywood Racks Sport Rider E-Bike Rack # HRSPRWH-F-HD to adapt your rack to carry fat tire bikes. These come as a pair of hoops for a single bike, so you'll need one of these for each bike you need to carry that has fat tires.
I've linked a short review and installation video of these for you to check out, as well. view full answer...
For your 2016 BMW X6 I recommend the Curt Trailer Hitch Receiver # 13077. This receiver fits all models including the M class.
For your wiring the ZCI Circuit Protected Vehicle Wiring Harness # 119250KIT will allow you to tie into your factory wiring without splicing any of the wiring on your X6. This will then connect to a 7-Way RV Upgrade Kit # ETBC7L. The upgrade kit will allow you to use the Curt Echo Trailer Brake Controller # C51180 for the brakes on your jet ski trailer.
The etrailer... view full answer...
Congrats on your recent purchase of the 24x60 etrailer Cargo Carrier # e98874 and the Light Kit # 98174LED! The correct brackets you need to install that light kit on your cargo carrier come in the kit # e98943-44.
I have attached some videos for you to check out. view full answer...
By saying you have a 2022 BMW X3i, I assume you mean either a 2022 BMW X3 xDrive30i or the sDrive30i. You are correct that we only have 2-inch hitch receivers that are available for all models of 2022 X3.
Although, there is a way to still use your 1-1/4" Class II accessory. For that route, I recommend using the Curt Trailer Hitch Receiver Adapter - 2" (Class III) to 1-1/4" - 4" Long # C45770 along with the Curt Hitch - 2" # C13387. With the adapter, you create a compatible 1-1/4" receiver... view full answer...
The Draw-Tite # 75600 and Curt # 13077 are the confirmed hitch fits for your 2015 BMW X5 so long as it is not the M model; for that model we have no hitch. Both of these hitch items are fairly involved installations as hitches go; you can refer to the linked video for the Draw-Tite.
For wiring, what you need depends on the trailer you intend to tow. For a basic aftermarket 4-pole harness that just carries trailer lighting signals (for a trailer with no brakes or other power requirements,... view full answer...
The Stealth Hitches Hidden Trailer Hitch Receiver w/ Towing Kit # SH22MR is rated for towing up to 6,000lbs with 600lbs of tongue weight. You will need to confirm the towing capacity of your 2020 BMW X5 M Competition with your BMW dealer to determine the vehicles towing capacity and if it is enough for your specific car and trailer.
For a brake controller I recommend Redarc Tow-Pro Liberty Brake Controller # RED52VR. This has a small dash mounted control knob which provides a clean appearance.... view full answer...
Go To Results