To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Quickly and easily install a 4-way trailer connector on your Honda CR-V with this custom wiring harness. T-One connector plugs directly into existing wiring - no cutting, splicing or tapping required. Powered ModuLite reduces strain on wiring system.
Features:
Specs:
Installation
This custom-fit T-One connector plugs into your vehicle's wiring harness, which is located in your rear cargo area, behind the driver's-side interior trim panel. Once you've plugged in the T-connector, open the fuse compartment beneath the driver's-side dash. Locate the fuse position indicated in the instructions, then insert the included fuse.
Once installation is complete, the 4-way flat connector will be stowed in your rear cargo area.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
A ModuLite power module is built into this T-One connector. Because most trailers run on a two-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your vehicle's three-wire system need to be combined so they are compatible with the wiring system of your trailer. This power module functions as a tail light converter to combine the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
With a ModuLite, your trailer's lights will be powered without overloading your vehicle's electrical system. Because the module draws power directly from your car's battery and bypasses the electrical routes that are used by a basic wiring harness, there is virtually no draw on your tail light circuits.
California residents: click here
Average Customer Rating: 4.9 out of 5 stars (700 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom wiring harness. T-One connector plugs directly into existing wiring - no cutting, splicing or tapping required. Powered ModuLite reduces strain on wiring system.
Everything showed up right. Installation on my CRV is a little more challenging than others I've done, but the videos were very helpful. I would definitely buy another hitch from etrailer.com and have referred people to them.
Quick and informed delivery. Item was as advertised. Will continue to use etrailer.com.
Charles
5/23/2024
Been a year and still working like a charm. Installation requires a little patience fishing some wires through tight spaces but not difficult. Very happy.
Perfect fit, installed like OEM harness. A bit of work to get behind the rear panel. The only downside is the size of the connector for the trailer. An in-between connector that would make it possible to thread the wiring through the SUV's body, without having to cut the wiring and reconnect each wire individually, would be ideal.
This product installed fairly easily, and the online installation video was a great help. It's working well for us. The video didn't exactly show how to add the fuse in the fuse panel under the driver's side dash, but a little more poking around online gave me the hints I needed. I'd definitely buy this product again!
Wiring little tough to install on Honda CRV. Watch the how to video for great instructions. When they say tight space they weren’t kidding. The hitch was a breeze. This is a great company with the best service. #3 for me from them overat least 10 years.
Pete
11/13/2023
This product works very well. Honda didn’t make it easy to install in a CRV. But the video available was very helpful.
Everything as expected. Have not installed yet, but instructions look clear. Looks like a quality product.
Steve
2/20/2024
Installation was easy and quick. If you want your Honda CR-V wired for towing, this kit is what you need.
Works get. Might be a little challenging for a first time DIYer to install. The video is a great resource. Could be better if the module extended into the spare tire well for fuse replacement. But being fused ahead in the car's system should keep me from worrying about it.
The product is great except the fuse that is with it does not fit my car. My car takes the low profile mini fuses not the regular mini fuses. I had to go to the store and spend another $[XX].
Easy to install, and works very well. Nice to have the harness in the vehicle, out of the elements.
This is my 3rs order from etrailer in 15 years, spanning 2 vehicles. They never disappoint. The install instructions that came with this were garbage, but etrailer had an amazing video (as did other sites) showing exactly how to install it. I'll keep coming back.
The design of the hitch, wiring and directions were excellent. Installation time was as stated. Dropping the exhaust system on a new car was a bit of a concern but after watching the video and following the tips given it was easier than I thought.
2024 CR-V Hybrid Sport Touring - Product was well packaged with everything needed to install. The video guide was accurate, and allowed for assembly.
I installed the Draw-Tite 76128 Hitch, the 118741 wiring harness and the 18144 bracket to mount the wiring plug. You can route the plug through the hole that is provided for the factory hitch wiring (it will fit through, but it is tight) and use the bracket to clean up the install. It looks pretty sweet doing it this way.
Tomb.
6/28/2018
I am still very satisfied with the installation as well as the products. They were put to use about a month ago towing a trailer from Central Vermont to Southeast Ohio. That was about 800 miles and absolutely no trouble.
Shipping was fast as always with these folks. Just got it today. I will be doing the install shortly. Not sure if this is my third or fourth hitch from them. Repeat customer. What else can I say but great people to work with. Thanks etrailer!
It was great I took it out and thinking about installation
thks again Kevin
Bought this hitch along with the wiring harness and 4-pole mounting bracket. My mechanic installed and it's been working great! Hauling well anytime needed!!
Hitch is working great. Installation went well with no issues - had a mechanic do the install. The hitch fits well on my Honda CRV 2018. Flush with rear bumper so no problem with leg scrapes. Support arms are barely noticeable as they sit up close to the underside of the car.
Danw
5/20/2020
After a year of use, the hitch looks great and has performed well. A little car wax helps keep it looking new. Have used it a few times over the year.
The products were great, and the service was even better. I wish I would have discovered etrailer years sooner.
Great product at a great price. Only suggestion would be to have a way to connect to the trailer wiring without having it being closed on by the tailgate of my CRV. I ultimately ran the cable into my spare tire compartment and then drilled a hole out near my trailer hitch and installed a grommet. Works and looks great but I had to cut the trailer connector off the T1 harness to dress the wires through my new hole and then reconnect it. The whole e-trailer experience and products were fabulous. I have a hitch and wiring harness that are as good as the Honda hitch/harness for hundreds of dollars less.
This was my second time purchasing trailer hitch and accessories from etrailer. Excellent price, service and the video of the installation was spot on. I would give them 6 stars if I could.
Perfect fit with great instructions. very helpful and knowledgeable customer service. Would highly recommend.
great kit eazy to install works great.
Super easy plug & play installation, and works great. I've been using it for over two years now, and it still works perfectly.
Second time I’ve bought a hitch and wiring harness, first time for 2013 CRV and now for my New 2019 CRV. I installed the hitch myself using car ramps it probably would have been easier with two people but it really is that easy if you are handy with your hands. You just need to take time with the wiring harness as the video suggests. Cost was less than 150.00 for both. My wife got an estimate for her SUV and the dealer wanted 650.00 for install. This was money well spent. Thank you etrailer.
etrailer is the best, thanks for all the vids guys! Makes the install a breeze! Much appreciated!
At the end of the Tekonsha wiring install vid it shows that the fuse was already installed on the vehicle. So sure enough, I turned my lights on and BAMB, my fuse was already installed as well.
I used a couple 2x4's to hold the panels back...
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Matt
3/17/2024
Have had this hitch on for about a year. Paint is chipping and its already rusting. Looks terrible already. Kind of disappointing.