How do I get the Trailer Harness Outside of My CR-V?

Question

Question:

In the video it look like he only ran the harness to the spare tire area, how do you get it to the outside of the vehicle where the hitch is?

asked by: ZACHARY B

0

Expert Reply:

The T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector item # 118741 hangs over the back bumper through the rear cargo area when it is in use. The door closing on the wires will not damage it. When its not in use you just roll it up and secure it underneath the floor in your CR-V.

expert reply by: Jerred H

0

Answer 1

The trim area is skewed to the drivers side. In the 2020 model year video, at the 4:15 mark you can see that it is skewed to the drivers side, or to say left of the tow hook. What our own installers do is to put one bolt in each side (closest to the…

view full answer...

Answer 2

In regards to the Curt Trailer Hitch Receiver part #c13397 which is a fit for a 2023 Honda CR-V, the trim diagram shows a cutout 3" wide x 1.375" tall, placed .625" to the right of the center rear fascia support tab. It sounds like…

view full answer...

Answer 3

For your 2019 Honda CR-V the Tekonsha T-One Vehicle Wiring Harness #118741 will work perfectly. This is a custom "plug-and-play" harness that features a high amp capacity for the lights and comes with Tekonsha's great reputation for…

view full answer...

Answer 4

I attached an install video for the T-One trailer wiring harness part #118741 that you referenced on a 2017 Honda CR-V just like yours for you to check out. At the 2:30 mark of the video you'll see our installer digging pretty deep into the…

view full answer...

Answer 5

For the Curt Trailer Hitch Receiver #C13397, we will have a video when we have the ability to get a 2017 Honda CRV into our installation bay. If you look at the installation details I've attached, you will see the look on the vehicle as well as…

view full answer...

Answer 6

There is a Class III trailer hitch with a 2 inch receiver that will not require you to cut the bumper fascia on your 2018 Honda CR-V, the Draw-Tite #76128. The reason why is because the Draw-Tite models has a visible crosstube, as you can see by the…

view full answer...

Answer 7

The first noticeable difference between the Draw-Tite #76128 and Curt #C13397 trailer hitch receivers for your 2019 Honda CR-V is the design and what it looks like after it is installed. The Draw-Tite looks like a standard trailer hitch where the…

view full answer...

Answer 8

For Curt trailer hitch #C13397 it is recommended to remove the lower fascia if your 2017 Honda CR-V has the hands-free liftgate option so that it and the sensor bracket can be trimmed. Regardless though removing the fascia or at least loosening it…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 12

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...

How do I get the Trailer Harness Outside of My CR-V?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching