Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Use this connector to connect your trailer to your vehicle to power the trailer's brakes and lights. Built-in magnet creates secure connection with an EZ Connector vehicle-end socket (sold separately). O-rings create a watertight seal.
Features:
Specs:
This trailer-end connector gives you the functionality of a 7-way, but without any pins or blades to bend or break. It's designed to work with a matching EZ Connector socket (sold separately) to create a secure, watertight connection that lasts. Strong magnets in both the plug and the socket keep the connection tight and secure, even when you're driving on rough terrain. Built-in O-rings create a seal to keep out water and debris. And spring-loaded, face-to-face electrical contacts are long-lasting and easy to clean. These factors combine for a strong, durable connection that's easy to use and to maintain.
The EZ Connector system uses magnets inside the plug and socket to hold the connectors together. Simply insert this trailer-end plug into the vehicle-end socket (sold separately) and the internal magnets will snap them together, no latch needed. To disconnect, just pull the plug out by hand.
This is an improvement over typical trailer connectors, which rely on a plastic latch on the socket lid to hold the trailer plug in place. With any trailer connector it can be easy to forget to disconnect the wiring when you unhook your trailer. If you drive off without disconnecting a standard 7-way plug, the connector will get pulled out of the socket, likely tearing off the lid. Without a lid, the electrical terminals are exposed to damaging moisture and debris. But if you forget to remove the EZ Connector plug when unhooking your trailer, the plug will disconnect from the receptacle as you drive off. And because there's no latch on the socket's lid to get in the way, the lid will automatically close to cover the terminals.
The magnet inside of this trailer connector is made of neodymium, an extra-strong, rare-earth alloy. This high-quality magnet ensures a tight connection between the connectors that is stable enough to make it through intense bumps and road vibration.
This trailer plug has 2 silicon O-rings that create a watertight seal when the plug is inserted into the vehicle-end socket (sold separately).
A storage holder is included to keep the plug safe and dry when it's not in use. This holder conveniently attaches to your trailer so that it is always available when you need it. Simply plug in the connector, and the plug's O-rings will create a watertight seal with the holder, just as they do with the vehicle-end socket. This ensures that the terminals on this trailer-end plug stay protected from moisture and debris at all times.
All of the EZ Connector systems have earned a perfect score on the SAE water submersion test. This means that the seal created on this connector, either with the plug holder or with the EZ Connector vehicle-end socket, will stay watertight, even if the connector is completely submerged in water for extended periods of time.
This EZ Connector plug has spring-loaded, face-to-face electrical contacts instead of pins or blades. Pins and blades can bend, corrode, and even break off, which can lead to a permanently damaged connection. With the EZ Connector system, there are no pins or blades to bend or break. Because there are no pins or blades, there are also no pin sockets on this connector that can trap debris. And if any dirt or debris does collect on the terminals of either end of an EZ Connector setup, it can be quickly and easily wiped away. No more scraping pins to get grime off. The result of all of this is a quality, effective connection every time you plug in.
Average Customer Rating: 5.0 out of 5 stars (21 Customer Reviews)
Use this connector to connect your trailer to your vehicle to power the trailer's brakes and lights. Built-in magnet creates secure connection with an EZ Connector vehicle-end socket (sold separately). O-rings create a watertight seal.
I replaced the standard 7-pin connector with the EZ Connector on my 5th wheel because I had problems with the trailer brake connection to my truck. This magnetic connector solved my issue and works so much better. No more time spent trying to fix a corroded connection, as this works every time. It's well worth the money!
Works great. My 2022 Escape TT has a pinbox so I removed the old 7 pin plug and cable and used it to cut each wire on the EZ Connector plug to the same length. Then I just matched the location for each wire with the assistance of a cell phone image. The two photos are before and after.
I really like the easy of use and security of how well it holds. A few small gripes though. One of the O-Rings tore very early on and I needed to order some replacements. Occasionally I don’t get a good connection and need to wiggle it.
The factory whip was coming loose from bumper connector,that prompted this product.Definitively step in right direction.
I had struggled with poor connector mating and fit with the standard connector until I changed to the EZ Connector Magnetic system. It's like a trailer sized Apple Magsafe connector. Mating is instantaneous and rock solid. In a perfect world every trailer connector would be an EZ Connector. My only gripe is that the mounting bracket would not stick down as far as it does. If they offered a minimum height connector bracket as an option it would be nice for those of us pulling trailers with passenger car SUVs and not pickup trucks with way more ground clearance.
I did not see a similar product with shorter length of wires or I would have picked it. There need to be more selections of products with several different lengths to make our individual needs met snd not waste the extra wiring as will be the case here. Other than that
I do think the product is is a great quality made item and look forward to using it on my trailer.
Great product. Should be standard on all trailers. I have multiple trailers and use them from salt winter Vermont roads to hot humid Florida roads. Usually get 6 months out of blade style 7 pin. These are far superior!
Install wasn't too difficult. My trailer had factory connections made with mechanical connectors. I disconnected all of the splices, pulled the pigtail out, pulled the interior wires out, soldered the EZConnector wires to the trailer wires outside of the trailer, applied the heat-shrink tubing, and pushed the wire bundle back into the trailer compartment at the same point they were previously. Worked perfectly with no additional work.
this product keeps connectors safe and clean and should be on every vehicle...they've planned very well to keep your equipment clean and out of the weather and dirt!!!!
Best way to get lights on a trailer. Only connections I will use now. I have them on both my trucks and every trailer I buy
This 7 way pin connector is heavy duty and well made.
Excellent product
Great help answering my questions. Service was A#1. I will return for any further business needs. Derek well done.
Products were good quality and arrived quickly
EXACTLY WHAT I NEEDED.
Do you have a question about this Trailer Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
John
5/3/2024
No issues. Still works every time. Connection remains strong and tight.