Summer Starts Here - Save up to 70%
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
4-1/16" x 1-1/16" Rectangle. Waterproof, LED trailer light serves as a side marker light or a clearance light. Pirhana series combines modern design with vibrant lighting. Surface mount - hardware not included. 2-Wire design. P2 rated.
Features:
Specs:
The waterproof construction of this light makes it ideal for use on trailers that may be submerged, like a boat trailer. The circuit board is sealed, which means that water will not damage the diodes or circuit board.
A P2-rated light produces a 45-degree angle of light to either side of its centerline for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side. So this type of light can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, then you must install 2 separate lights on your trailer - one as a front or rear clearance light and one as a side marker light.
Surface-mount trailer lights install using a flange or bracket with mounting holes. These lights lay flat against the trailer surface and only require a small, often pre-existing hole, for wiring. Mounting hardware is used to secure the light to the trailer.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we'll be taking a look at the Peterson Piranha LED clearance or side marker trailer light.This is a submersible light since it's epoxy sealed, so that going to keep all our diodes from any kind of corrosion or any kind of damage. That means we can use this on a marine trailer anytime we're going in and out of the water, or just any other trailer that we want to have an amber clearance light. And we'll know that it's going to be protected from any kind of dirt or debris from getting in there and causing issues.Those LEDs are also going to have an advantage over the old incandescent bulb styles since there's no brittle filaments that can break with these. There's no bulbs to replace. They're virtually maintenance free once you install them in. And they're going to last a lot longer, have a lower power draw, and give you typically a brighter light than you would get with your incandescent bulb.
You have this amber lens going over our white LEDs. It is compatible with 12 volt DC systems.When I hook this up to my power and ground, our black wire will be for the power and then our white wire with the ring terminal on it is going to be our ground. It comes with a number 10 ring terminal already on our ground wire there. So I'll turn on my power .. you can see our LEDs come on.
We'll have those two diodes. Turn out the lights in the studio and you can get an idea of how bright that is.So not super bright, but enough to be DOT compliant and let other drivers know where we are at. This is P2 rated, which means that you can see it head on but then when we turn to the side it's really not as visible. This can be used as a clearance light or a side marker light. It can't operate as both since you can't see it at that full range of view.
Turn the power off. Disconnect my wires. Let's go over some measurements.The light is about 4 and 1/8 inch long, or 4 and a 1/16 inch long. Excuse me. And then about 1 and 1/16 inch wide.
And about an inch thick or about 15/16. The wires coming off the back are about 5 and 1/2 inches long.You can pick up a bracket to go with this. That part number is sold separately, but you can find that here at etrailer.com. And that's going to be part number B169-18. And it's just a little black bracket, but this is going to pop in too. The wires go through the middle, and then you would attach it using the holes here on either side. The hardware to get this mounted up is not included either so you'll have to pick that up separately as well.This is DOT compliant. P2 rated, again. And it has a power draw at 12 volts of 0.03 amps. Input voltage can be between 9 volts and 16 volts DC, and it comes with a 10 year limited warranty from Peterson. Overall, it should be a really nice looking long lasting light for your trailer.That's going to do it for our look at the Peterson Piranha LED clearance and side marker lights. One last measurement I want to give you is the distance between our mounting holes. That's three inches. And that'll do it for our look at the Peterson Piranha LED clearance lights.
Average Customer Rating: 4.8 out of 5 stars (275 Customer Reviews)
4-1/16" x 1-1/16" Rectangle. Waterproof, LED trailer light serves as a side marker light or a clearance light. Pirhana series combines modern design with vibrant lighting. Surface mount - hardware not included. 2-Wire design. P2 rated.Replaced poorly designed lights on a travel trailer with these. The original lamps were not weather proof and used tensioned contacts that were prone to oxidation and corrosion from the elements. These LED lamps are sealed in epoxy so the elements will not affect them. Each lamp has two LEDs and a 6" wiring pigtail.
These are the best trailer lights I’ve found... super fast shipping...great place to do business with. Will definitely do business with them again.
I was looking for specific trailer lights to match my existing. E trailer had all of the selections and I will definitely use again!
I have ordered several time at etrailer and every time has been like I'm the first customer on their list. My order was always shipped and delivered in short time and in good condition. No issues at all. I highly recommend etrailer to everyone.
nice as advertised, make sure you get the rubber gasket with it,.....
good light, dose not come with mounting screws
I needed one for a replacement ....ordered 2 to have a extra on the shelf
Dave
4/6/2024
Perfect
Product was exactly as described, just what I needed. And they shipped in a very timely manner. Thanks
Product was just what we needed. It replaced a broken one on a Hummer. Thanks for responding so quickly.
just what I was looking for
These are far better than the bland factory lights and are sealed very well.
The lights worked great for our Timpte hopper trailer.
Easy to install and fit holes from previous installation.
Not sure its anyones fault but the LED marker lights on my trailer fasten to the wall with screws and today that style is not made as it was in 2017...So i am rating the lights "average" cause till i open the light up without busting it I got to make it work and your lights are just the same as the rest...lights look fine and i will let you know how it works out...
Order 2 of theses paid extra for shipping , and they don't match each other dame part number , tried to return them wad going to cost me more thank just keeping the wrong parts does not match pictures on website
Good service fast shipping
These lights were the perfect brightness, very rugged, and easy to install inside protected areas of the frame on the updated raft trailer. etrailer has great selection, the website makes it easy to find the best parts for the job, and their communication is excellent. Their videos and reviews are invaluable.
came quick and was an exact match
Just starting using you guys and the service, website and deliveries have been great. Keep up the great work.
The 168R side marker light paired with the B168-18 mounting gasket were easy to mount and work perfectly.
Do you have a question about this Trailer Light?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Eric R.
10/24/2018
LIghts still working a year later