Parts Needed to Tow a Small Trailer with a 2018 Ford EcoSport
Question:
I just bought a 2018 ecsport se...not sure if it is a 3 cylinder engine. But, it is a front wheel drive, can this hitch support a small Trailer for a interstate move? So far I like the product but I am not a mechanic and would need a shop to install it. Also, the video showed that other hardware supplies were needed. IE., the parts to prevent rattling and chain c-clamps. Could someone give an estimated cost for those and where to find them?
asked by: Diane R
Expert Reply:
The Draw-Tite Trailer Hitch Receiver # 36660 will fit your 2018 Ford EcoSport SE no matter what size engine you have so you are good to go on that end of things (plus the EcoSport in the video is an SE). The hitch comes will all of the hardware to get it mounted as well. Please note that even though this trailer hitch has a max trailer weight rating of 3,500 lbs, Ford has determined that the max towing capacity for your EcoSport is 2,000 lbs so that is your limiting factor.
For a ball mount that is compatible with an anti-rattle device I recommend the Curt # C45026 (use in the Rise position) which has a hollow shank that allows you to use the anti-rattle pin # F-315 or for a locking option part # e98879. You also need a hitch ball. Use part # A-80 for a 1-7/8" diameter or part # A-82 for a 2" diameter. Your trailer coupler will say what size you need to tow it.
The chain C-clamps you mentioned should actually come with the trailer as it is against the law (for safety purposes) to tow a trailer without the chains. If for some reason your trailer doesn't have them just let me know and I can help you figure out which ones will be best for your application.
One last thing that you'll need is a wiring kit to activate the trailer lights. I recommend using the Curt # C59236 which you can see we installed on the same 2018 EcoSport as the trailer hitch. If you only plan on towing this one time for your interstate move then I would just leave the plug located in the rear hatch like what the installation video shows. If you plan on towing occasionally then it might be worth having your shop install the plug next to your hitch receiver using brackets # 18144 and # C57202.
I have attached some review videos and helpful articles on towing for you to check out. The only other thing I recommend picking up is the hitch cover # 22281 which will help your hitch receiver to last longer on the inside.
Products Referenced in This Question
1-7/8" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Stainless Steel - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Stainless Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- CURT
more information >
2" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Stainless Steel - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Stainless Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- CURT
more information >
Curt Class I Drawbar - 2-5/8" Rise, 3-1/4" Drop - 9-3/8" Long - 2,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- CURT
more information >
Curt No-Drill Bracket for 6-Way or 7-Way Round Trailer Connector Mounting Bracket - Long
- Accessories and Parts
- Trailer Wiring
- Mounting Hardware
- Brackets
- 6 Round
- 7 Round
- CURT
more information >
Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Universal Fit
- 4 Flat
- CURT
more information >
etrailer Trailer Hitch Receiver Lock for 1-1/4" Hitches - Flush - 2-1/8" Span - Chrome
- Trailer Hitch Lock
- Standard Pin Lock
- Keyed Alike
- Chrome
- Fits 1-1/4 Inch Hitch
- Flush Pin
- 2-1/8 Inch Span
- etrailer
more information >
Trailer Hitch Anti-Rattle Kit for 1-1/4" Trailer Hitches
- Hitch Anti-Rattle
- Standard Anti-Rattle
- Universal
- Fits 1-1/4 Inch Hitch
- Threaded Pin Style
- Accessory Anti-Rattle
- CURT
more information >
Product Page this Question was Asked From
Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class II
- 350 lbs TW
- 3500 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Curt Class I Drawbar - 2-5/8" Rise, 3-1/4" Drop - 9-3/8" Long - 2,000 lbs
- Article: How to Measure for Trailer Hitch Drop
- Shop: Curt Class I Drawbar - 5" Rise - 9-9/16" Long - 2,000 lbs
- Shop: Draw-Tite Drawbar for 1-1/4" Hitches - 5" Rise - 10" Long - 3,500 lbs
- Shop: Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
- Shop: Curt Class I Drawbar - 4" Rise - 9" Long - 2,000 lbs
- Shop: Curt Class II Drawbar - 3-7/8" Rise - 13-1/2" Long - 3,500 lbs
- Shop: Roof Rack
- Search Results: sportrack replacement parts
- Shop: Trailer Hitch
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Choosing the Right Trailer Wiring
- Shop: etrailer Hitch Pin Alignment Collar for Hitch Accessories - 2" Hitches
- Search Results: 44649
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Video: Choosing the Right Brake Controller
- Search Results: 68149
- Shop: Trailer Wiring
- Search Results: 25580
- Article: Trailer Wiring Diagrams
- Shop: Brake Controller
- Q&A: Adding Brakes to a Mobile Home Axle
- Shop: Suspension Enhancement
- Article: The 5 Best Trailer Drop Hitches You Can Buy
- Search Results: dust cap
- Video: Timbren Axle-Less Trailer Suspension System Installation
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: dust caps
- Shop: Gooseneck Hitch
Diane P.
3/27/2020
Doesnt these accessories come in a Kit so as to save money, instead of individual pricing items??Thanks!