Pre-Drilled Round Rubber Trailer Bumper - 96" Long x 2-1/16" Wide
(63 reviews)
Price: $104.72
Pre-Drilled Round Rubber Trailer Bumper - 96" Long x 2-1/16" Wide
Item # D2-96
Our Price: $104.72
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (63)
- Q & A (0)
- Photos
Redline Trailer Door Parts - D2-96
- Ramp Door Bumpers
- Bumper Strip
- 2-1/16 Inch Wide
- Rubber
- 96 Inch Long
- Redline
This round rubber bumper protects the rear of your trailer and provides cushion for your cargo as you load and unload.
Features:
- Round rubber bumper helps prevent damage to the rear of your trailer
- Provides cushion to protect your cargo as you load and unload
- Pre-drilled holes make it easy to bolt onto your trailer
- 5/8" Bolts are not included
- Made in the USA
Specs:
- Overall dimensions: 96" long x 2-1/16" wide x 2" tall
- Pre-drilled bolt hole diameter: 5/8"
- Distance between holes on center: 11-1/2"
- Distance from last hole to end of bumper on either side: 2"
- Number of holes: 8
| Width | A | B | C | D | No. of Holes | Bolt Size |
|---|---|---|---|---|---|---|
| 2-1/16" | 96" | 5/8" | 2" | 11-1/2" | 8 | 5/8" |
Round Bumper
Initailly designed to mount on the rear of horse trailers to prevent damage to the trailer and the cargo, pre-drilled rubber bumpers have quickly risen in popularity with builders of all types of trailers.
D2-96 Pre-Drilled Round Rubber Bumper - 2-1/16" x 96"
Customer Satisfaction Score:
93% were satisfied with this product
7% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- Defective
Customer Reviews
Pre-Drilled Round Rubber Trailer Bumper - 96" Long x 2-1/16" Wide - D2-96
Average Customer Rating: 4.8 out of 5 stars (63 Customer Reviews)
This round rubber bumper protects the rear of your trailer and provides cushion for your cargo as you load and unload.by: Aaron04/17/2024
Exactly what I needed it to be. Has held up and been good for a year. Nothing wrong with this if you need one. :-)
by: Philip10/16/2022
Product is as described, some tips on installation might be helpful. Plus you mention to use 5/8 bolts, which seemed rather large! I used 1/2” and seems to do the trick. I also added a backing plate inside the bumper as this one doesn’t come with one.
by: Michael04/03/2022
This was a replacement for my 20 year old trailer which no longer supplied replacement parts. It needed some modifications, but worked well, and has lasted.
I'll buy from etrailer again as I have in the past.
by: Tonya 08/29/2023
We use this rubber bumper to make several small ones. Works perfectly.
by: Mike W.03/09/2015
Needed a rubber bumper for my horse trailer. Good price and quick shipping. Product arrived on time. Will use again in the future.
by: Catherine 12/01/2023
Excellent service, would buy again from them, thankyou cat and simon
by: Bob L07/15/2016
First I would like to thank etrailer for their fantastic customer service. I rebuilt an old trailer using exclusively parts from etrailer. Every part exceeded my expectations. I haul many horses for a rescue organization and getting those horses in and out of a trailer can be an interesting experience. I put this bumper on the back of the trailer to help protect their legs. After a year of hard use the bumper looks like it is brand new. Unlike some bumpers I have used in the past, this one stands up to horses, has not chipped or pulled away from the trailer.
Bob L.
7/15/2017
With very heavy use, product has held up beyond expectations.
by: Tim F.06/01/2017
A year later and still going strong! The rubber bumper was difficult to put on...in part because I had to drill holes in my trailer, but it has been a great addition and saved more than one horse. So glad we did it.
Tim F.
6/1/2018
Its been a valuable addition to our trailer, but it was very difficult to install.
by: Not perfect but OK07/15/2017
In my case I had to install this with a reinforcement bar inside.
Be advised that on a drawbridge trailer door, when installed full length, I had to adjust the door tension due to the weight.
I like it. and it certainly is better at protecting the door corners than the tiny round bumpers the trailer came with so I am pleased.
etrailer does not sell (nor does the manufacturer) an end cap (plug) so I made one out of aluminum. I think they should have at least been offered, if not included.
by: Tim M.11/18/2014
I have not installed the bumper yet. The quality seems to be good. My only problem is that it doesn't come with mounting hardware or any instructions for mounting. Our trailer did not previously have a bumper, so we didn't have any hardware,nor could we see how it is mounted.
by: Tracy05/05/2016
Had this installed on my horse trailer when I removed the cumbersome ramp. A year later it's still protecting my horses' legs as they unload.
by: JamesGary09/08/2022
Was delivered on time and was what I expected for quality and ease of installation.
by: Dawn09/27/2018
Super service- product worked great! Used the predrilled rubber trailer bumpers on a slipper steep horse trailer ramp.
by: Hillbilly-G07/11/2018
Wheel spacers for larger tires and continuous door bump strip were just what my enclosed trailer needed.Speedy delivery and fair priced- Thanks
by: Kevin10/26/2018
Wow, wish I new about etrailer.com previously. Product was exactly as described and fit our trailer correct, arrived supper faster! Will continue to utilize this site.
Thank you,
by: Mark C05/27/2015
Arrived in perfect condition. Super fast delivery. Just what I needed for my horse trailer. Very easy to install. Had no problems at all.Good high quality. Recommend etrailer will buy from again.
by: Doug 05/25/2021
Just what I was looking for to replace rear bumper of my horse trailer. Fair price, quick delivery makes this purchase all the better.
by: Karl 09/20/2022
Wish that came with hardware and reinforcement but I'll make it work thank you
by: Daniel 08/20/2021
Good bumper. Should work well. Yes the holes are pre drilled but you have to make the outside holes bigger to get a washer and bolt inside and then the socket. They might as well no pre drill the holes. Seems like good quality rubber and should last a while.
by: Marianne12/07/2017
Just received the rubber bumper. Product looks good. I know it will look great on my horse trailer. Very fast shipping and service. Thank you
by: Nolberto06/22/2020
Product as described. Quick shipment and great tracking
by: Rex Hezlitt05/25/2018
Bumper came quickly and was easy to install, hardware not included, but simple nuts and bolts found at local hardware store.
by: Tammy 04/15/2021
It worked great, just what we needed for our trailer
by: Jeff W.11/02/2016
Recieved order promptly. Product was exactly as described. Prices were competitive. Thanks for your good customer service.
Jeff W.
11/2/2017
Great. As hoped
by: Gibbs03/19/2019
Always great service and products arrive as advertised. Thanks once again!
Gibbs
3/23/2020
24 stock trailer - heavy use - holding up well.
25
63
Show More Reviews
See what our Experts say about this Redline Trailer Door Parts
- Can Washer Be Used Under Head Of Bolt To Mount Round Rubber Trailer Bumper D2-96?If you can squeeze a washer through the hole with the head of the bolt, then you can absolutely use one to mount the Pre-Drilled Round Rubber Trailer Bumper - 96" Long x 2-1/16" Wide # D2-96 to your bumper, but one is not required even though you do not have a backer bar as long as you use the correct 5/8" diameter bolts. Keep in mind that mounting hardware is not included so you will need to source it from your local hardware store. I included a video of the # D2-96 for you to take a look at.
view full answer... - Does Pre-Drilled Round Rubber Trailer Bumper # D2-96 Have Metal Backing PlateThe Pre-Drilled Round Rubber Trailer Bumper # D2-96 that you referenced does not come with any metal framing inside of it. I attached a picture the bumper with it flexed to show you it doesn't have anything metal inside of it.
view full answer...
- Separating Brake and Turn Signals, Adding a Reverse Light, and Ramp Door Support for a TrailerFirst, trailers in the US use what is called a combined 2-wire system. The brake lights and turn signals are on the same circuit on each side. The turn signal overrides the brake light on the side blinking. In order to have separate turn signals you would need additional amber turn signals and you would need to do some rewiring. On the trailer side you would need to install a special converter, # 118158. The combined left turn/brake wire connects to the yellow input wire, right turn and...
view full answer... - Changing a Trailer Ramp Door To Barn Doors On A 6x14 V-Nose Enclosed TrailerTo create barn doors out of your ramp door, you will need hinges and a latch. I suggest a latch/lock system like the Universal Cam-Door Lock for Enclosed Trailers - 1" Keeper, # 383200. This will use a 3/4 inch diameter pipe that you'll have to get at a local hardware store, but the bridge-type keeper prevents accidental opening and ensures safe locking action. It will also allow you to use a separate lock like # ML1KA to secure your cargo. We will also need hinges similar to Strap...
view full answer... - Replacement for 84 Inch Bumper on Horse TrailerAll of our bumper strips are 96" long and have the holes pre-drilled out at 11" on center, but the nice thing is these can be cut and re-drilled to accommodate your application. You just need to choose which one has the width you're looking for: 2-1/16" Width - # D2-96 3" Width - # D3-96 4" Width - # D4-96 So these will definitely work, you'll just need to do some modification to make it work.
view full answer... - Is Specific Mounting Hardware Required for Pre-Drilled Round Rubber Trailer BumperThe Pre-Drilled Round Rubber Trailer Bumper # D2-96 is designed to be used with 5/8" Bolts, which are not included, so you'll just want to source it from your local hardware store. The bolt holes are pre-drilled so you don't have to worry about cutting through the rubber with a drill before mounting. When it comes to cutting to size, you should be able to cut it fairly quickly using a rotary tool or pair of shears and it shouldn't be too difficult using the right tools.
view full answer... - Center To Center Hole Spacing on Redline # D2-96 Rubber BumpersThe holes in the Redline # D2-96 Pre-Drilled Round Rubber Bumpers are 11-1/2 inches on center. You can see the full dimensions by looking at the photo I've edited for you.
view full answer...
- Rubber Bumper Options for Rear of Horse TrailerWe have 3 different rubber bumpers that you can use for your horse trailer. They all measure 96" long but have different widths so you'll just need to choose the appropriate width: 2-1/16" Width - # D2-96 3" Width - # D3-96 4" Width - # D4-96 These can be cut to length and modified as needed. There are holes every 11" but if you need mounting locations different than that you can drill out holes to fit your application. Attached is a review video for you to check out.
view full answer... - Recommended Trailer Bumper ReplacementWe only sell trailer bumpers in 96 inch lengths, but they can be cut to size. We have a 4 inch option # D4-96, a 2-1/16 inch option # D2-96, and a 3 inch option # D3-96. The holes are 11 inches apart and have a 1-1/4 inch diameter
view full answer... - Can Custom Holes be Drilled Into a Redline Pre-Drilled Round Rubber BumperSince the Redline Pre-Drilled Round Bumpers, part # D3-96, part # D2-96, and part # D4-96, are made of rubber I see no reason why you cannot drill out mounting holes so that they are custom to your hole patterns. If you will be using the full 96 inches of the bumpers then you may want to consider drilling more mounting holes in your trailer so that the bumper has more support. I recommend drilling out holes to match the rest of the pre-drilled holes to avoid more drilling. Keep in mind...
view full answer... - Round Rubber Horse Trailer Bumper Guard Needed That's 84" LongThanks for reaching out, Tracey! The 96" Long Pre-Drilled Round Rubber Trailer Bumper # D2-96 is the only length that we carry. If the pre-drilled version works best for your application I recommend picking this one up and then trimming it to best suit your needs. Since this is just a big piece of rubber you won't be causing structural damage by trimming on 12" of it.
view full answer... - Can Pre-Drilled Round Rubber Bumper - 2 inch x 96 inch be Cut to Fit the Width of 60 inch TrailerYes, the Pre-Drilled Round Rubber Bumper - 2 inch x 96 inch part #, D2-96 can be cut down to fit any application you may have. After going out into the warehouse and looking at the bumper I recommend either using a utility knife to very carefully cut it, or securing the rubber tightly and using a sawz-all to make the cut.
view full answer... - How to Install Redline Pre-Drilled Round Rubber Bumper # D2-96The Redline Pre-Drilled Round Rubber Bumper # D2-96 can be installed in a variety of ways depending on the nature of the trailer. The holes are drilled all the way through to allow user-supplied hardware to mount it. We also offer a larger size bumper # D3-96 that measures 3-inches x 3-inches. No special tool is required for installation; you will use whatever tool is appropriate for the fasteners you choose.
view full answer... - Rubber Bumper for Stock TrailerWe do have some rubber bumpers for you to install on your stock trailer. They are all 96" long so it just depends on what kind of width you're looking for: 96" Long x 2-1/16" Wide - # D2-96 96" Long x 3" Wide - # D3-96 96" Long x 4" Wide - # D4-96 These come pre-dilled with holes every 11" but you can cut these to length and drill new holes to match your application if you need to. Attached is a review video for you to check out.
view full answer...
Do you have a question about this Trailer Door Part?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Jameson C
Installed by:
Jeff D
Updated by:
Adele M
Updated by:
Laura H
Updated by:
Shelly K
Updated by:
Hannah L
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Michael
4/4/2023
It is working well with no sign of deterioration a year later.