Center To Center Hole Spacing on Redline # D2-96 Rubber Bumpers

Question

Question:

How far apart are the pre-drilled holes-on center?

asked by: Kathy

0

Expert Reply:

The holes in the Redline # D2-96 Pre-Drilled Round Rubber Bumpers are 11-1/2 inches on center. You can see the full dimensions by looking at the photo I've edited for you.

expert reply by: Mike L

0

click to enlarge

Answer 1

The Redline Pre-Drilled Round Rubber Bumper #D2-96 can be installed in a variety of ways depending on the nature of the trailer. The holes are drilled all the way through to allow user-supplied hardware to mount it. We also offer a larger size…

view full answer...

Answer 2

Since the Redline Pre-Drilled Round Bumpers, part #D3-96, part #D2-96, and part #D4-96, are made of rubber I see no reason why you cannot drill out mounting holes so that they are custom to your hole patterns. If you will be using the full 96…

view full answer...

Answer 3

The Pre-Drilled Round Rubber Trailer Bumper #D2-96 that you referenced does not come with any metal framing inside of it. I attached a picture the bumper with it flexed to show you it doesn't have anything metal inside of it.

view full answer...

Answer 4

We only sell trailer bumpers in 96 inch lengths, but they can be cut to size. We have a 4 inch option #D4-96, a 2-1/16 inch option #D2-96, and a 3 inch option #D3-96. The holes are 11 inches apart and have a 1-1/4 inch diameter

view full answer...

Answer 5

If you can squeeze a washer through the hole with the head of the bolt, then you can absolutely use one to mount the Pre-Drilled Round Rubber Trailer Bumper - 96" Long x 2-1/16" Wide #D2-96 to your bumper, but one is not required…

view full answer...

Answer 6

Yes, the Pre-Drilled Round Rubber Bumper - 2 inch x 96 inch part #, D2-96 can be cut down to fit any application you may have. After going out into the warehouse and looking at the bumper I recommend either using a utility knife to very carefully cut…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

You can put a maintenance charge on your trailer battery with the 12 volt accessory circuit of the 7-way. The 1:00 position of your 7-way carries this circuit. You would just need to run a length of 10 gauge wire like part #10-1-1 (sold by the foot),…

view full answer...

Answer 10

I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I am…

view full answer...

Answer 11

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Center To Center Hole Spacing on Redline # D2-96 Rubber Bumpers

Product Page this Question was Asked From

Continue Researching