Can Pre-Drilled Round Rubber Bumper - 2 inch x 96 inch be Cut to Fit the Width of 60 inch Trailer

Question

Question:

Can this bumper be cut to length. My trailer ramp is about 60 inches? Thanks

asked by: Stephen W

0

Expert Reply:

Yes, the Pre-Drilled Round Rubber Bumper - 2 inch x 96 inch part #, D2-96 can be cut down to fit any application you may have.

After going out into the warehouse and looking at the bumper I recommend either using a utility knife to very carefully cut it, or securing the rubber tightly and using a sawz-all to make the cut.

expert reply by: Jameson C

0

Answer 1

The holes in the Redline #D2-96 Pre-Drilled Round Rubber Bumpers are 11-1/2 inches on center. You can see the full dimensions by looking at the photo I've edited for you.

view full answer...

Answer 2

We only sell trailer bumpers in 96 inch lengths, but they can be cut to size. We have a 4 inch option #D4-96, a 2-1/16 inch option #D2-96, and a 3 inch option #D3-96. The holes are 11 inches apart and have a 1-1/4 inch diameter

view full answer...

Answer 3

The Pre-Drilled Round Rubber Trailer Bumper #D2-96 that you referenced does not come with any metal framing inside of it. I attached a picture the bumper with it flexed to show you it doesn't have anything metal inside of it.

view full answer...

Answer 4

The Redline Pre-Drilled Round Rubber Bumper #D2-96 can be installed in a variety of ways depending on the nature of the trailer. The holes are drilled all the way through to allow user-supplied hardware to mount it. We also offer a larger size bumper…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

You can put a maintenance charge on your trailer battery with the 12 volt accessory circuit of the 7-way. The 1:00 position of your 7-way carries this circuit. You would just need to run a length of 10 gauge wire like part #10-1-1 (sold by the foot),…

view full answer...

Answer 7

I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I am…

view full answer...

Answer 8

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 10

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 11

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Can Pre-Drilled Round Rubber Bumper - 2 inch x 96 inch be Cut to Fit the Width of 60 inch Trailer

Product Page this Question was Asked From

Continue Researching