Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This powder coated steel receiver clamps around your RV's 4" square bumper to provide a 2" x 2" trailer hitch receiver opening. Perfect for hitch accessories or light-duty towing.
Features:
Specs:
Note: For use with RV-approved accessories only.
Tech Tip
No drilling required for installation
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello everybody, this is Jeff at etrailer.com. Today we're gonna take a look at this Ultra-Fab two inch Motor Home Trailer Hitch Receiver for four inch by four inch steel bumpers, has a 3,500 pound gross towing weight capacity. Now, this powder coated steel hitch receiver is designed to clamp around your RV's four inch square bumper, and it provides this two inch receiver opening for your hitch mounted accessories such as bike racks, cargo carriers, or you can even use it for light towing. Now, this hitch receiver can only be mounted onto a four inch square continuous steel welded bumper, it's not designed for aluminum bumpers. This is a heavy-duty steel construction, does have a maximum gross trailer weight capacity of 3,500 pounds. Now, one note on that is you do not wanna exceed the weight rating of the bumper it attaches to, and it has a maximum tongue weight of 100 pounds.
If you noticed, if I show you the bottom of it, you can see it does have the safety loops on each side for connecting your safety chains to. We mentioned the black powder coat finish on it, provides rust and corrosion resistance, and this is a nice bolt-on installation, it includes all the mounting hardware, you can see I've pretty much installed it onto the part just to show you where it all goes, and it comes with a nice set of instructions that'll describe how it all goes together. Now, also I wanted to show you, if you look closely, right here and right at the very bottom, there's two large bolts here, these thread into the hitch receiver, and the reason those are on there is once you put your accessory in there, you tighten those down on the bottom and on the side, and it'll help reduce movement between the hitch mount and the receiver tube. Again, the application, you can see the U-bolts here, they are designed to fit four inch by four inch continuous steel welded RV bumpers. Receiver opening right up here is two inches by two inches, and one note is this is designed for use with RV approved accessories only.
Let me show you all the sides. But that should do it for the review on the Ultra-Fab two inch Motor Home Trailer Hitch Receiver for four inch by four inch steel bumpers.
Average Customer Rating: 4.7 out of 5 stars (220 Customer Reviews)
This powder coated steel receiver clamps around your RV's 4" square bumper to provide a 2" x 2" trailer hitch receiver opening. Perfect for hitch accessories or light-duty towing.Installed this hitch on my fifth wheel to pull my side by side to the upper peninsula in Michigan, however I would recommend that you be sure your bumper is capable of the weight being towed. I personally removed my existing bumper and welded on a much heavier steel bumper. This hitch did exactly what was expected of it, thanks so much to Kirstin for her help at checkout
Works great used on trailer bumber for portable refrigerator to carry on cargo unit. Had to beef up bumper with angle iron due to weight ...no bounce at all with hitch
This bracket provided me the means to mount the receiver style spare tire b racket on my Class C RV. By mounting it upside down, it placed the weight squarely on the frame, leaving the u-bolts to merely hold it in place.
The product arrived ahead of schedule. etrailer upgraded my shipping at no extra cost! It fit on my bumper with very little problem. It was tight because of my chrome covering, but I expected that. I did have to replace two of the nuts that would screw on, and I had wanted to place it above the bumper but the body of the trailer wouldn't let me. I haven't gotten a bike carrier yet, but I wholly expect it to work just fine. I would have given it an excellent but for the bolts I had to replace.
I needed a way to carry our mountain bikes when we go traveling with a our RV. The Ultra-Fab Hitch receiver fit perfectly on the 4x4 rear bumper allowing me to carry our bike rack. I feel I could even tow my golf cart trailer behind my RV with this hitch if needed. Very easy to install with a simple socket set and torque wrench.
Product fit perfect. Easy to install. Very happy with the hitch, Only one problem, the anti-wobble bolt on the side would not fit because U-bolt is in the way. You can only get the bottom anti-wobble bolt in. (See 2 pictures) I solved that problem by cutting off the end of the U-bolt that was in the way. They just need to move that hole back a bit more. Now I have both bolts on and cargo carrier is solid.
This bolt on hitch worked as advertised. Important to get the bolts sufficiently tight. I used this product to hold a cargo carrier on 2020 Colorado camping trip.
Very easy to install (my four year old helped me). We used it for our bike rack on the back of the trailer so it was installed on top of the bumper instead of underneath. This thing holds it very solid.
Cold the cargo rack on the rear of our travel trailer.I bought it so that I can lock my generator to it when we’re traveling.
hooked up hitch both u bolts broke dropping both bicycles on freeway in Montana. Just a fact and no total rack and bikes were well un der the maximum load rateing,
This fit very well, only problem is the side anti wobble bolt won’t fit when the U bolts are installed. Note submitted picture.
Kenneth
6/5/2022
Just ground off a 12 inch or so, installed bolt before the U bolt. Works fine now.
Product looks and feels very solid and well made. Only took me 5 mins to install. Can't wait to see how it performs as we head out in the next few days. I will be carrying my generators and gas and kids bikes on it. Thank you again etrailer.com for an easy purchase with all of the info i could ask for on your website to help make the best selection for my needs.
Works as advertised. Simple to attach. I use it on the back of my camper an put a generator, extra fuel and loaded cooler. Thanks for great product.
The bolts on the top are not long enough. I had to buy longer bolts. The bolt on the side that secures the hitch to reduce the movement is too long. The u-bolt is in the way. I had to buy a shorter bolt. The bolt hole needs to be repositioned so the u-bolt will not interfere.
the item looked and worked as advertised
Well constructed, very easy to install, negates fabricating or adapting a hitch by taking advantage of existing 4" bumper.
E trailer is a consistent place I shop for fast delivery, great communication and products as described.
Will not slide properly over my 2” hitch, machined wrong, the holes for the hitched pin indent in on the hitch, will not work. This is my second try, I wish they would inspect there products before sending them out as I am stuck with no way to move.. will be asking for a full refund.very disappointed!!
David B.
9/20/2022
This is for mounting on motorhome bumpers not to mount on hitch receiver bars.
Bought (2) of them to make to make a removable rack for a small inflatable boat to carry on the back of the trailer bumper. Appears plenty strong have to see how it lasts. Did notice that the chain loops interfere with the 5/8" bent hitch pin hair pin connection. I'll have to make one out of a bolt (they should have though of that).
Victoria B.
10/24/2019
Rather than a bolt, I recommend using a straight hitch pin, such as the etrailer Trailer Hitch Lock # e98882. This hitch pin has a locking end cap to keep your hitch accessory secure. The lock core is accessed on the end of the cap, making it easier to access in a hitch with limited space like this one.
Helpful Links
So far it was very easy to put on the Trailer, I used it for a cargo carrier to place a 3000 Honda Generator on the carrier, work great, the next thing I'm going to try is to pull my 2 Waverunners, but I will check the weight first..
Rich A.
7/3/2014
It has worked great, but now I have changed my Trailer and do not need it anymore
The Ultra fab 2" RV Hitch Receiver for 4"x4" Bumpers is a very well made piece of steel. It fits our Wildwood Trailer Bumper perfectly. It is built so sturdy we have no worries about using it to haul our bicycles. It is rated at 3.5k!
Rachael H.
5/23/2017
Thanks for the review Ron, but please also keep in mind that an RV approved bike rack should be used, and please make sure the bumper is appropriately for your use.
I mounted 2 on my camper bumper. One for a bike rack and the other for a swing away grill. Super happy w the product and the results.
Dave P.
3/24/2021
A year later, I couldn’t imagine not having the bikes and the grill on the back of the RV. Great product
Very sturdy attachment. Fit perfectly on the trailer bumper and hardware was 1/2" Grade 8 Cad plated--good stuff. Order was received at my driveway exactly on schedule. I would continue to do business with etrailer.
Robert G.
12/1/2018
The attachment is working great. I need to store it outside and see no physical deterioration.
I didn't use these as recommended, but they are working great. Most people mount one of these on the back bumper of their RV and then attach some way to carry a storage box or a bike rack. I didn't like the way they flop around going down the road. All that movement isn't good. Instead I purchased 2 of them and mounted them inline with the frame rails, then welded together a rack to affix a standard pickup tool box and mounted it in the hitches. This supports it from both sides and is stronger since it is mounted inline with the frame rails. They are working great and prevent any movement in the box. It's a rock solid mount.
Do you have a question about this RV and Camper Hitch?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Mark N.
9/11/2019
This product has preformed as it should, no issues and I can be confident that it will withstand its purpose, thanks again