T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
(154 reviews)
Price: $62.96
In Stock
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
Item # 118411
Retail:$87.11
Our Price: $62.96
You Save: 28%
Will this fit?
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (154)
- Q & A (0)
- Photos
Tekonsha Custom Fit Vehicle Wiring - 118411
- Custom Fit
- Trailer Hitch Wiring
- 4 Flat
- Powered Converter
- Tekonsha
Quickly and easily install a 4-way trailer connector on your vehicle with this custom wiring harness. T-One connector plugs directly into existing wiring - no cutting, splicing or tapping required. Powered ModuLite reduces strain on wiring system.
Features:
- Provides a 4-way flat trailer connector at the back of your vehicle to power your trailer's signal lights
- Compatible with 5-pole, 6-pole and 7-pole adapters (sold separately)
- Connects quickly and easily - no cutting or splicing of wires
- Locate connection points in rear cargo area
- Plug in T-connector
- Run hot lead to existing power cable stud
- Includes ModuLite to ensure that your vehicle's wiring matches that of your trailer
- Powered module connects directly to battery to avoid overloading vehicle's electrical system
- Constructed of 16-gauge bonded wire
- Comes with dust cap for 4-way flat connector
Specs:
- Maximum amperage:
- Stop/turn lights: 2.1 amps per circuit
- Tail lights: 5.6 amps per circuit
- 1-Year limited warranty
Installation
This custom-fit T-One connector plugs into your vehicle's wiring harness, which is located behind the driver's-side and passenger's-side interior trim panels in your rear cargo area. Once you've plugged in the T-connector, locate the power cable stud on the driver's side. Then connect the fuse holder wire with the ring terminal to the stud.
Once installation is complete, the 4-way flat connector will be stowed in an out-of-the-way location within your cargo area.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
ModuLite Powered Tail Light Converter
A ModuLite power module is built into this T-One connector. Because your vehicle runs on a multiplex wiring system, the wiring needs to be converted to be compatible with the wiring system of your trailer. This power module functions as a tail light converter to combine the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
With a ModuLite, your trailer's lights will be powered without overloading your vehicle's electrical system. Because the module draws power directly from your car's battery and bypasses the electrical routes that are used by a basic wiring harness, there is virtually no draw on your tail light circuits.
118411 Tow Ready T-1 T-Connector - 4 Wire - Modu-Lite
Installation Details
This Product Fits The Following Vehicles
- 2005 - 2014 Volvo XC90
California residents: click here
Customer Satisfaction Score:
97% were satisfied with this product
3% of customers were not satisfied
- Product did not meet expectations
- Wrong item was ordered
Customer Reviews
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector - 118411
Average Customer Rating: 4.8 out of 5 stars (154 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom wiring harness. T-One connector plugs directly into existing wiring - no cutting, splicing or tapping required. Powered ModuLite reduces strain on wiring system.by: Cory 01/16/2024
2005 Volvo XC90
Got what I ordered. Etrailer never disa ppoints.
by: Rob F.11/27/2014
2008 Volvo XC90
Very easy installation on the XC90. Clipped off the flat 4 connector and picked up a power line directly from the battery for wiring to a 7 blade connector (pulling a 2 horse trailer with the XC90 V8 Sport). When wiring this up, take the battery out of the vehicle which makes dressing the wires much easier and also gives you access to the battery power distribution strip if you are running a hot line back to the connector. This harness saves a lot of time and is a more reliable connection. All lights and functions work great.
by: Alain 03/28/2024
Was installed a yeAR AGO - WORKS PERFECTLY AND A FAIRLY EASY INSTALL.
by: Tanyon06/06/2023
2006 Volvo XC90
I only received one item. The box was mutilated when I received it’s the wire harness was missing.
by: Tony04/09/2022
Ordered on a Tuesday arrived on fri installed on sat. No lift one person took alittle over an hour to wrestle hitch into place and complete wiring
by: Josh07/10/2019
Installation of this wiring harness went really smoothly. Another review had said they had difficulty in reaching/seeing the connection point inside of the Volvo XC90 but I found the gray connector is connected inside the compartment with a plastic barb - so once I pulled that free I was able to see what I was doing. It was a real time saver to be able to simply plug in the connetiions with no need for making splices or having to worry about which wire goes where. It IS a little inconvenient to have the flat plug running out through the tailgate and so I routed my trailer plug out of the bottom through an existing rubber boot/grommet near the battery (which required spliceing the lead but it works GREAT.
Josh
7/11/2020
My wiring harness is working just as perfectly as the day I installed it. I put a tiny bit of dielectric grease in the boot to keep the connectdisconnect easy and I’m a very satisfied customer
by: ColoradoRoger08/02/2011
Volvo
Product was fairly easy to install, however the recommended installation location of the four pin connector jack was, at best, bush league. If installed to directions, the plug is to be stored inside the vehicle and be draped out of the tailgate when towing.
The manufacturer should design a way to disconnect the four wire lead, so it can be easily threaded through a Volvo grommet and reconnected to the harness. The four wire plug should then be attached to the receiver for both use and storage.
Shawn
8/1/2015
You can easily run this through the bottom...and get an extension of the 4 prong as you described. Often when 4 prongs hang out the vehicle they will eventually corrode. Youll want that extension to easily pull off and replace every 3-5 years. Done this twice on my XC70s and now researching XC90s
Rachael H.
8/3/2015
Thanks for the information Shawn. If you would like an extension we have the Spectro Wiring # 9653P, but do be aware we do recommend using dielectric grease like # 11755. We also recommend using a mounting bracket like the # 18144, and if you would like a no-drill option we offer the # 18140 or # 18136 that can be used with the # 18144 to secure the 4-flat mounting bracket to your hitch without drilling.
by: Steven01/30/2023
I haven't been able to find a email related to the receiver hitch that I purchased from you and that is the item that I was considering writing the reviews for. When I received the box I didn't notice any damage but when I went to install it. It was bent and would not install.
by: Richard06/22/2019
2010 Volvo XC90
I purchased a Drawtite hitch for my 2010 Volvo XC90 . The shipping info was provided quickly and the hitch and wiring harness kit arrived in a few days . Today I installed the hitch it took about 30 minutes once on the lift . Instructions were accurate and the hitch fit perfectly with zero issues . I haven't installed the wiring kit yet but I'm sure that will be no issue either . I would order again with no hesitation .
Richard
6/23/2020
The hitch is still performing well which is to be expected . The wiring harness install was a breeze definitely much easier than splicing like the old days .
by: Andy S07/31/2015
2009 Volvo XC90
Bought wire harness (item 118411) for a 2009 XC90 3.2 AWD. Installation was exactly as the description and video mentioned. Have had no problems with the quality or workmanship of the product. Item to note- I had the harness exit the rear of the vehicle from the bottom of the lower tailgate as the pinch area was rubber and loose enough to allow the wire to shift if necessary and not tight enough to crush the harness. Great product.
Andy S.
7/30/2016
Its been a year now and the trailer harness has worked to perfection. No drain on the cars electrical system and the mating connector has held up like new. Also, considering that the wire harness must exit the vehicle pinched between the upper and lower tailgate the harness has not been compromised at all due in part to the quality of the harness sheathing and the rubber seals on the tailgates. Item to note on the XC90- run the harness out the center of the tailgate rather than the rear left side or you run the risk of burning the harness with exhaust gases.
by: Brian 12/14/2019
2014 Volvo XC90
Etrailer video on the installation was so good, I watched it before I ordered and was able to install it in 45 minutes without any further references to the video and instructions. I was so confident in my install that I had my 14 year old son watch me install it and talked him through the process as though I was an expert. Worked perfectly on my Volvo XC90 2011.
Brian
12/15/2020
Works GREAT. Stays hidden when not in use.
by: Michael02/28/2018
This appears to be a very high quality product. I connected it all in about 15 minutes. you cant actually see the wires that you have to disconnect but thanks to the video on this website it made it much easier to see. The only reason I didn't give this video 5 stars is I do not like the fact that the wire hangs out the tailgate. I bought an extension for the 4 plug trailer harness and will look for a way to run the wire through a grommet or something to the outside for a correct finish in the future. It would be nice if etrailer figured out a way to do this, even if it involves some drilling or something and provided a video for more capable installers to have another option for a more finished look.
Mike L.
3/1/2018
There are a couple of reasons Tekonsha recommends installing the trailer wiring harness you purchased so that the trailer connector is stored in the interior of the vehicle. Installing the connector in this manner greatly simplifies the installation, making it much easier for those who arent the most mechanically inclined.This method is typically recommended for vehicles that are primarily passenger vehicles that wouldnt be used for full-time towing. Keeping the connector in the cargo area of the vehicle helps protect the connector from the elements and from damage from road debris.The weatherstripping on the rear hatch or trunk of the vehicle is plenty thick enough so that closing the door on the wiring harness wont harm it, as long as the wires are kept away from the latch. I used a set-up similar to this for towing my PWC trailer for years, and it worked great.
by: Jay 02/16/2020
I am not a mechanic, but somewhat handy.. I found this to be super easy to install, and was able to reference the great videos that etrailer.com provides. If I get another vehicle, I will surely do my own wiring for adding a trailer. Thanks for making this very easy.
Jay
2/22/2021
still working great!
Jay
2/22/2021
still working great!
by: Sean06/24/2019
relatively easy install. Only time consuming part was interior removal/install to hide the harness, and to run the power wire to battery. Aside from that, the actual harness install as plug and play!
Sean
6/25/2020
after a year of towing, the harness has given me zero issues. no complaints here, quality seems to be holding up fine as well. I use it around 20x in the summer and thats it
by: Nsee-John08/11/2020
2006 Volvo XC90
Ordered a Draw-Tite Class III hitch and a Tekonsha wiring harness for installation on an SUV. Choosing the appropriate hitch and wiring kit for my particular vehicle was made especially easy given the very thorough video that explained the pros and cons of various products in a side-by-side comparison. Once the products arrived, the instructional installation videos were a significant help in explaining the installation process. I had some concern with in installing the hitch myself as the installation process required disconnecting and slightly lowering the rear portion of the exhaust system on my particular vehicle. The instructional video, tailor-made for my particular vehicle, showed how to do this. I easily installed both products in a couple of hours with no assistance. Kudos to etrailer for great quality products, fantastic up-front virtual customer assistance (videos), clear directions, and ease of installation. This satisfied customer would highly recommend them. They have just added another customer for life!
by: Joey F05/28/2016
2014 Volvo XC90
I purchased this wiring harness for my 2014 Volvo XC90 and installation was quick and easy. Total time was about 20 mins, with most of that time fishing for the existing wires in the Volvo. I couldn't beat the price from e-trailer either, this was purchased with the Hidden Hitch Trailer Hitch Receiver (Class III - product 87810) and I installed myself. Total price for both was around $240, as opposed to the Volvo Dealership who wanted over $750 just for the parts and another $150-200 for installation. The video instructions to installation is an extra mile customer service by e-trailer. That video made the installation so easy. I have, and I will continue to, recommend e-trailer to friends.
by: Micah V V05/24/2014
2011 Volvo XC90
Arrived on time and was pretty easy to install after watching the multiple videos from the etrailer website.
I didn't understand when I ordered this for my 2011 Volvo XC90, but the actual wiring plug stays in the car under the floor in the spare tire compartment, and then you just pull it out through the back hatch and close the hatch on it if you need to hook up trailer lights. I was hoping the connector would mount onto the trailer hitch itself for easier plugging in and also it would look better, but this will work fine.
by: Charles04/15/2018
2008 Volvo XC90
Bought this wiring harness along with an after-market trailer hitch. I don't intend to pull a trailer (bumper carrier only) but I figured I should have lights just in case. Installation was easy. No drilling or modifications needed. Works fine through a test light.
by: Volvo XC9010/23/2010
Volvo XC90
Volvo XC90 wiring installationOnce the correct plugs were identified, it was pretty straightforward. The video link was very helpful, but what the instructions may add is that there are THREE sets of grey electrical plugs on each side of the vehicle. EACH of the three plugs is physically different, and two of them are out in the open where you can easily see and reach them. The third, the one you NEED, is tucked in behind the panel and physically attached to the sheet metal of the car, so it is somewhat harder to find, and MUCH harder to access. (the video shows it already located and pulled off the panel, the written instructions are vague and of little help here.)
Alston
3/31/2014
I have the same problem that you had. Except that I cannot get to the connector. How did you get to the connector behind the panel.
Dave
2/19/2016
Yea, that plug was tough to get at. I had to use a screwdriver to work it loose from the sidewall.
by: Bob K.08/02/2017
2011 Volvo XC90
I ordered a trailer hitch and light package from etrailer.com. The materials arrived on time and were in perfect condition. The installation instruction and videos were precise which made the installation easy. After installation, I trailed a boat 800 miles from Pennsylvania to South Carolina without issue. I highly recommend etrailer.com and I will definitely rely upon them in the future.
by: dwight04/27/2017
2006 Volvo XC90
Almost 5 stars... delivery was on time and most of the install went well. Instructions must have been for a previous model year as I did run into a couple of minor surprises. The harness was purchased as part of a towing package. The hitch install was a bit of real work, but doable and instructions were good. Only missing the receiver pin and clip which Etrailer sent out quickly. Quite satisfied with Etrailer service and products.
by: Todd06/19/2018
2011 Volvo XC90
Direct fit and plugged in to my 2011 Volvo XC90. Took me about an hour to install. I like the ease of storing the wires inside the car when not needed.
Todd
6/19/2019
It continues to work well, no issues to date.
by: Donald 05/17/2020
The hitch fit my vehicle absolutely perfectly and installed within 45 minutes (mostly because I had to lower the exhaust a few inches. The wiring harness for the hitch also installed very easily mainly because of the excellent installation video on the etrailer web site. Great job!
by: Andrew K.11/26/2018
2019 Volvo XC90
I located my connection points for my E-TRAILER harness were tucked behind (and not attached to) the interior panels as shown in the video on how to install this harness into a Volvo XC90. It was a bit cold when I installed it (it was raining as well), so I did not get a video done. I will more than likely do a video sometime in the spring of 2019.
by: Chris B09/08/2013
2015 Volvo XC90
I installed the trailer wiring harness for my Volvo XC90 in approximately 15 - 20 minutes. Installation was very simple following the related installation video. Excellent way to show your customers how to install the product since written instructions can be confusing. The connections for the wiring harness connected to the factory plugs perfectly. Excellent product, factory looking installation, fast shipping, and great customer service.
25
154
Show More Reviews
See what our Experts say about this Tekonsha Custom Fit Vehicle Wiring
- Recommended Trailer Hitch for 2008 Volvo XC90For your 2008 Volvo XC90, the trailer hitch you want is actually the Curt Trailer Hitch Receiver # 13559. This is the only Draw-Tite hitch confirmed to fit. For your wiring harness, you will want the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118411. This custom-fit T-One connector plugs into your Volvo XC90's wiring harness, which is located behind the driver's-side and passenger's-side interior trim panels in your rear cargo area. Once you've plugged in the T-connector,...
view full answer... - Running Light Pin has Power All the Time on Trailer Wiring Harness for a 2008 Volvo XC90If the trailer has LED lights then it is possible that there is some bleed over because wiring harness # 118411 is a powered converter. To see if this is the issue you can unplug the fuse from the fuse holder. If the issue stops then this is likely what the problem was. If the trailer does not have LED lights then it could be some corrosion where the harness connects to the vehicle on the drivers side. Look for dirt or corrosion and also any bent of broken pins. If this continues to...
view full answer... - Ball Mount, Balls, and Trailer Wiring Recommendations for a 2007 Volvo XC90 with Draw-Tite HitchFor your 2007 Volvo XC90 and Draw-Tite trailer hitch # 75152 I recommend etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag. If the ball mount kit does not have the right rise or drop to tow the trailer level, use the link I have included that explains how to measure to choose a ball mount to tow the trailer...
view full answer... - How to Remove Connector from Vehicle Body to Install the Tow Ready Wiring for a 2009 Volvo SC90You might need to use a trim panel removal tool like our part # ALL648544 to get the connector disconnected from your vehicle body on your 2009 Volvo XC90. A flathead screwdriver might work as well. Thats what we had to do to access the connector in the install video I attached for this product.
view full answer... - Wiring Question 2006 Volvo XC 90 Trailer Lights Not Functioning ProperlyI would start off checking all of my ground connections and tracing all the trailer wires to be sure none are broken or shorted. The first place I always look is where the license plate mounts with the taillight on the left side of the trailer. The lights are most likely grounded through the mounting connection to the frame and if the bracket is plastic it can sometimes interfere with the connection and cause problems. If the ground connection is not the problem and the trailer wiring...
view full answer... - Installation of the T-One Vehicle Wiring Harness, Part # 118411, on a 2007 Volvo XC90The T-One Vehicle Wiring Harness, item # 118411, is installed inside the vehicle access panel area at the rear of the vehicle. You will need to remove the cargo access door on the floor, the floor trim panels and the access panels on each side of the vehicle. The T-connectors will then be installed inline with the vehicle taillight wiring. You will need to install the ground wire to a suitable ground location and install the power wire to the vehicle power cable stud which is located on...
view full answer... - Availability of a Vertical Receiver Hitch for a 2014 Volvo XC 90The Curt vertical receiver adapter, part # C45013 is designed to work only with the Curt Stealth Hitch, but it might possibly work with other vertical receivers. We currently don't offer a vertical hitch receiver, only an adapter. The crucial dimension will be distance from the center of the hitch pin hole on the vertical tube to the end of the receiver. If this distance is more than 7/8 of an inch, the Curt adapter # C45013 will not work for you. See the diagram to the right. If you...
view full answer...
- Can Trailer Hitch from 2010 Volvo XC60 Be Used on 2012 XC90?We do have a hitch fit for the 2012 Volvo XC90, but unfortunately the 2010 Volvo XC60 and and a 2012 XC90 use different hitches. For the 2012 XC90, I'd recommend the Curt Class IIl hitch, part # 13559. If you'll be towing with the hitch, you'll also need a trailer wiring harness, part # 118411, a # C45010 ball mount and for a trailer ball, use # 40038 for a 1-7/8 or # 63845 for a 2 inch ball.
view full answer... - Trailer Hitch For 2013 Volvo XC90 For Towing TrailerFor your 2013 Volvo XC90 go with the following hitch: - Curt Max-Frame Trailer Hitch Receiver # 13559 And since you'll be doing some towing, the other thing you'll need for your XC90 is a trailer wiring harness, with the correct fit for your vehicle being the T-One Vehicle Wiring Harness # 118411.
view full answer... - Can Redarc Tow Pro Liberty Install on 2008 Volvo XC90 without Interfering with ComputerWe can help you install the Redarc Tow Pro Liberty part # RED24FR and it won't interfere with the computer of the vehicle at all as it does not integrate in any way with it. The first thing you'll need is a 4-way like the part # 118411 if you do not have one already. Then you'll need to use the # ETBC7 to convert it to a 7-way and wire in the controller. Your stoplight switch circuit may be hard to access on your vehicle so you may also need the # RM-751000.
view full answer... - Adding a 7-Way and Brake Controller to a 2007 Volvo XC90 with 4-Way ConnectorI will be happy to help. There are a couple of ways you can add a 7-Way trailer connector to your 2007 Volvo XC90. If you just want the lights to function on the trailer then you can use # 37185. Your 4-Way will plug into this adapter and then you just have to mount it and ground the white wire to a bare metal surface. The other wires can be taped up and stowed out of the way. If you want to have a fully functional 7-Way and a brake controller then instead of 37185 you will need # ETBC7....
view full answer... - Brake Controller and Trailer Hitch Recommendations for 2012 Volvo XC90The Curt Class III trailer hitch, part # 13559 would be an excellent choice. The hitch installation is pretty simple. If you view the attached installation instructions, you can decide if the installation is something you'd feel comfortable attempting yourself. You'll also need a ball mount like part # 2923 and a trailer ball like part # 19260 for a 1-7/8 inch ball or # 63845 for a 2 inch. If the trailer has brakes, and you want them to actuate, you'll need to install a brake controller....
view full answer... - How to Convert a Trailer With Separate Brake/Turn Signal Wiring to work with A Combined Tow VehicleYou are going to need to use a taillight converter to convert the separate taillight signal of your trailer to the combined signal of your tow vehicle. For this you will want to get a Vehicle to Vehicle Tail Light Converter # C56196. You will want to cut off whatever trailer connector is on your trailer and then wire up the right turn signal to the green wire of the output side of the # C56196, the brake light signal to the red wire of the output side and the left turn signal to the yellow...
view full answer...
- Trailer Hitch and Wiring for a 2009 Volvo XC90 with Dual ExhaustCurt trailer hitch # 13559 is listed as a fit for all models of the 2009 Volvo XC90 including those with dual exhaust! Installation will be the same except that instead of lowering one exhaust pipe you would have to lower both in order to get into position. I have linked the installation instructions for you. If you plan on doing some towing I recommend etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise...
view full answer... - Is the Installation the Same for a 2006 Volvo XC90 Compared to the Video For a 2004 or 2007 XC90From my research it looks like the first generation of the Volvo XC90 runs from 2002 - present (2014) with a minor facelift in 2007. The installation process is same as either the 2004 or 2007 for your 2006 Volvo. The installation of this Curt # 13559 hitch does not require additional drilling, it does require minor fascia trimming. It is recommended to temporarily lower the exhaust and spare tire for installing this hitch. I would think that one helper would suffice. I have included...
view full answer... - Recommended Trailer Hitch For and Towing Capacity of 2005 Volvo XC90Based on my research, it looks like the 2005 Volvo XC90 has a towing capacity of 4,000 to 5,000 pounds, depending on the exact model. With this in mind, I still strongly suggest taking a look at the owner's manual for the vehicle or verifying this information with your local dealer before purchasing it to tow your pop-up camper or 3,000 pound trailer. For a trailer hitch that is confirmed to fit the 2005 Volvo XC90, I recommend the Draw-Tite Class III # 75152. This Class III hitch features...
view full answer... - Trailer Running Lights Not Working Only When Starting Volvo XC90 Engine I honestly haven't heard of this type of issue before. Just to be clear, when you just have the light on in your Volvo the trailer lights work perfectly but when you actually start the vehicle the running lights stop working? If this is the case then the best thing I can recommend trying is testing the wires that are going to the black converter box on the Tekonsha T-One # 118411 with the vehicle running with a circuit tester like # PTW2992. Check to see if you are getting power on the...
view full answer... - Will the Spare Tire Fit in the Factory Location On the Volvo XC90 After the Hitch is InstalledThe spare tire will be reinstalled in the factory location after the hitch installation is complete on your Volvo XC90 (see instructions link). If you'll be towing with the hitch, you'll need a few products to complete your towing system: Trailer wiring harness with 4 pin trailer connector # 118411 Ball mount # C45010 Pin and clip # PC3 2 inch trailer ball # 63845 1-7/8 inch trailer ball # 19260 If you use the provided links, you can view an install video showing the hitch and wirng...
view full answer... - Does Trailer Hitch and Wiring Communicate With the Engine and Transmission on Volvo XC 90Your Volvo XC90 will require the T-One Vehicle Wiring Harness with 4 Pole Trailer Connector, item # 118411. This wiring harness will protect your vehicle's sensitive wiring and computers from electrical shorts and mis-wired trailers. There is no wiring harness for trailer towing that communicates with the vehicle engine or transmission. The trailer wiring cannot communicate trailer weight or any other information to the vehicle. Your vehicle powertrain control module (PCM computer) senses...
view full answer... - How To Convert 4-Way To 5-Way Trailer Wiring on My 2005 Volvo XC90We actually have a 4-way to 5-way adapter that will connect to your existing 4-way connector on your 2005 Volvo XC90. You will need to use the Adapter 4 Pole to 5 Pole, part # 20036, which will plug into the 4-way on your Volvo. Then, as you stated, you will run the included blue wire and splice into the reverse light circuit, making the connection with the included quick splice. You will need to use a circuit tester, like part # PTW2993 to find the reverse light wire. I have linked a...
view full answer... - Are Hitches Available for a 2008 Volvo XC90 Made with Square or Round TubeAll the hitches we offer for your 2008 Volvo XC90 use square tube construction. No drilling, trimming or vehicle modification will be required, the hitch bolts to existing holes in the vehicle. The nice thing about the design of the hitch is that the cross tube is concealed behind the bumper, so the receiver tube is the only visible portion of the hitch. The two hitches available are pretty similar, visually speaking but the Draw-Tite # 75152 has a higher tongue weight capacity (maximum...
view full answer... - Trailer Hitch and Wiring for a 2013 Volvo XC90 All-Wheel DriveYes, the Curt trailer hitch # 13559 will fit your 2013 Volvo XC90 all-wheel drive. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag. If the ball mount kit does not have the right rise or drop to tow the trailer level, use the link I have included...
view full answer... - Where Does Power Wire for Trailer Wiring Harness 118411 Install on a 2013 Volvo XC90On your 2013 Volvo XC90 you aren't looking for a wire to splice the power wire from harness # 118411 to. That power wire will get a ring terminal clamped to it and go over a power stud located directly next to a fuse on the driver's side. Everything else just plugs in. I included a picture showing the stud in question.
view full answer...
- How To Get Camper Lights Working Using Tow Ready Adapter # 30717 on 2005 Volvo XC90 With 4-WayFirst, on the # 118411 wiring harness you installed on your 2005 Volvo XC90 check the 4-Way connector with a circuit tester like, like part # PTW2993, to make sure the 4-Way is working correctly. If it is not, check to make sure you have the white wire from the wiring harness attached to a good ground and the yellow power wire from the converter box installed to the fuse box on your vehicle correctly with a good fuse installed in the fuse holder. I am including a link to a video that will...
view full answer...
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
Test Fit:
Joe V
Test Fit:
Randy B
Expert Research:
Mike L
Expert Research:
Robert G
Expert Research:
Michael H
Expert Research:
Reno H
Expert Research:
Jameson C
Expert Research:
Jeffrey L
Video Edited:
Zack K
Video Edited:
Joshua S
Video Edited:
Jacob T
Video Edited:
Andrew L
Video Edited:
Kathleen M
Updated by:
Laura H
Updated by:
Wilson B
Updated by:
Alexander C
Updated by:
Isabelle B
Installed by:
Cole B
Video by:
Alan C
Video by:
Chris R
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Jenny N.
6/8/2023
Oh my goodness! Sounds like the box had quite a trip. I will have our Customer Service team reach out to you.