T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector

See what our Experts say about this Tekonsha Custom Fit Vehicle Wiring

• Activating 12 Volt Accessory Circuit of 2014 Dodge Ram 2500 7-Way
  It's possible your truck is missing wiring but we aren't as well-versed in the wiring setups for every vehicle. I'd say though that it's very likely your truck is an anomaly and is missing wiring as that circuit is normally active on Ram trucks like your 2014 Ram 2500. Instead of dealing with the headache of trying to track down all of the possible missing wiring I have a better solution to activate this circuit. Use a length of 10 gauge wire like part # 10-1-1 (sold by foot) through a...
  view full answer...
• Adding 4-Way Flat to 2000 Chevy Silverado with Factory 7-Way
  Since your 2000 Chevy Silverado is equipped with the factory 7-Way connector all you will need to add a 4-Way is the Tekonsha T-One Wiring Harness # 118384. This will plug right in-line with the 7-Way (no splicing, cutting, etc) to provide you with a 4-Way flat that you can use for your new light bar. Because of how it installs it will also retain function of the existing 7-Way. I have attached an installation video that you can use for reference as well.
  view full answer...
• Suggested Ball Mount for Curt C13043 Hitch Installed on 2010 Lexus GX460
  When we installed the Curt # C13043 on a Lexus GX460, we found that once installed the top inside edge of the receiver tube sits 17-3/4 inches above the pavement. The receiver would protrude past the rear bumper by roughly 2 inches. A standard-length ball mount with a 2-inch drop such as the # C45010 would work fine for you and would put the majority of trailers within 1-1/2 or so inches of level, which is plenty close enough. For a trailer ball, use # 19260 for a 1-7/8 or # 63845 for...
  view full answer...
• Availability of Local Installer for Draw-Tite Trailer Hitch Receiver on 2012 Jeep Grand Cherokee
  We can help with a local installer for the # DT38MR on your 2012 Jeep Grand Cherokee Laredo. I have attached a link below which will take you to a list of professional installers near Columbia, SC. You can change the zip code if yours is different. If you plan on doing some towing with your Jeep you will also need wiring. If you do not have the tow package you need the # 118425 and if you do have the tow package the # 118384. The wiring harness will provide you with a 4-way to power your...
  view full answer...
• Interior Lights In Horse Trailer Not Working After New Tow Vehicle
  If the only thing that has changed on your trailer is that it is now being pulled by a different vehicle then that is most likely where the issue resides. Generally speaking, the interior lights are powered by either a 12 volt battery on the trailer and is then charged by the 12 volt power circuit on the 7-way or they are just ran directly to the 12 volt power circuit on the 7-way. Therefore, the issue you are having is most likely that the 12 volt power circuit on the 7-way is not active...
  view full answer...
• Recommendations for a Complete Setup for Towing a Travel Trailer with a 2010 Lexus GX460
  I can help you get set up with all the right equipment for towing a travel trailer with your 2010 Lexus GX460. Let's start with what you will need for the vehicle itself. The hitch I recommend for your 2010 Lexus is the 2 Inch Draw-Tite # 75685, this custom fit hitch has a tongue weight capacity of 500lbs and a towing capacity of 5,000lbs. which will work great for your trailer. Next for the vehicle you will need wiring to power the taillights on the trailer. Your Lexus should already...
  view full answer...
  
• Hitch Recommendation For a 2010 Dodge Ram 2500 Mega Cab With a Factory Installed Hitch
  You might want to check the hitch on your 2010 Dodge Ram 2500, but it is usually welded on to the frame of your vehicle. It would be very difficult to remove. I would recommend the Curt Class V 2 Inch Hitch, part # C15409. This hitch has 17000 lbs towing weight capacity and 2550 lbs tongue weight capacity. If you will be towing with the Curt hitch you will also need the Draw-Tite Ball Mount, part # 40331, the part # PC3 Pin and Clip, and the hitch ball. Depending on the coupler size...
  view full answer...
• 7-Way Trailer Connector Recommended for 2016 Chevy Traverse
  I'd be happy to help you with that. Even though you don't have the 'factory tow package', your vehicle is already prewired for a 7-way and a brake controller, if you need one. For the 7-way, you can use part # 118271 that will plug into the connector under the bumper. The kit includes the fuses and relays needed to activate the tow package. For a 4 pin connector, you can either use an adapter like # PK12716, or you can use a t-connector like # 118384 that would plug into the connection...
  view full answer...
• Will the Primus and P2 Brake Controllers Work with Standard Electric Brake Systems on a 2011 Tundra
  The Tekonsha Prodigy P2 Brake Controller, item # 90885, will work with both standard electric trailer brakes, and electric over hydraulic braking systems. I have attached a link to instructions for you to review. The Tekonsha PRIMUS IQ Brake Controller, item # TK90160, is not designed to work with electric over hydraulic braking systems, but will work great with standard electric trailer brakes, see instructions link. The P-3 brake controller is also compatible with both standard electric...
  view full answer...
• 12 Volt Power All the Time On Brake Output Circuit with Curt Brake Controller on 1999 Olds Bravada
  There should not be power on the brake output wire unless the brake controller is sending back power. It sounds like something might be miswired at the 7-Way. Take a look at the picture I have included that shows the pin out of a vehicle side 7-Way trailer connector to make sure yours is wired the same way. If it isn't then put the wires in the appropriate places. Also check to see if any of the wires are touching each other inside the 7-Way. And if the 7-Way is dirty or corroded that...
  view full answer...
  
• Right Side Trailer Lights Do Not Work on Trailer Towed by 2005 Nissan Titan
  Since the lights on the trailer are working fine on another truck that would mean the issue is on your 2005 Nissan Titan. It sounds like a bad ground. Ground problems normally show up when there is more draw on a system such as when you have the running lights on and then use another function like a turn signal or brake light. Or they can happen as the result of corrosion or loose wiring. Make sure that the vehicle side and trailer side connectors are clean and free of corrosion inside...
  view full answer...
• Trailer Wiring Harness Kit Options for 2011 Chevrolet Traverse
  Curt 4-Pole trailer wiring harness kit # C56245 fits the Chevrolet Traverse for model years 2013 through 2017. For your 2011 Traverse we do offer similar plug-and-play wiring kits and the correct one will depend on how the car is equipped. If you have the factory tow package the car will have a round U.S. Car connector under the rear bumper that will accept a 4-pole plug-in harness # 118384 or a combination 7-way/4-pole harness like # HM40975. If the car does NOT have the factory tow...
  view full answer...
• How to Install 4-Way Trailer Connector on 1999 Chevrolet Silverado 1500 with Factory Tow Package
  The Tow Ready T-One Wiring Harness, part # 118315, is for the 1988 to 2000 Chevrolet C/K Series trucks. It is not for the 1999 Chevrolet Silverado 1500. The 1999 Chevrolet Silverado 1500 would use either the Tow Ready Wiring Harness, part # 118384, which is used if you have a harness that is located under the vehicle, behind the bumper, on the driver’s side of the vehicle. The wiring harness # 118384, is meant to plug in line with the factory wiring and provide a 4-Way flat connection....
  view full answer...
• Is Any Trimming or Cutting Needed when Installing Draw-Tite # 75699 on a 2011 Jeep Grand Cherokee
  The installation of the Draw-Tite Class III 2 Inch Hitch, part # 75699, on a 2011 Jeep Grand Cherokee Limited will not require any cutting or trimming of the plastic fascia in the rear of the vehicle. It will use existing bolts and weld nuts on the vehicle. I am including a link to the installation instructions on the Hidden Hitch. To complete your towing setup, you will need the following items: Draw-Tite Ball Mount, part # AMSC2 Pin and Clip, part # PC3 Tow Ready 2 Inch Hitch Ball,...
  view full answer...
• 4-Pole Trailer Wiring Harness for 2002 GMC Sierra
  If your 2002 GMC Sierra does not have a round U.S. Car connector to accept a 4-pole trailer wiring harness like # 118384 then it should have a bundle of wires tucked up above the spare tire (see the linked article, step 3, section B). The yellow wire is the left turn and brakes, dark green wire is the right turn and brakes, brown wire is for the taillights, and white is the ground. To these you can attach a 4-pole plug like # 18252, connect the wires color for color with heat shrink butt...
  view full answer...
• Trailer Wiring Harness for a 2001 Chevrolet Tahoe with LED Tail Lights
  It sounds like you are trying to install a trailer wiring harness on your 2001 Chevrolet Tahoe with aftermarket LED tail lights. If that is the case then you can use the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector part # C59236 which is compatible with LED tail lights. This is a hard wire option that will require you to splice into the tail light circuits on your Tahoe. However, if you do not already have a US car connector plug (see photo) on your Tahoe then this...
  view full answer...
  
• No Power on 12-Volt Accessory Pin on 7-Way of 2005 Chevy Silverado
  How to proceed will depend on what you meant by not getting any power to my trailer. If the 12-volt accessory power pin that's in the 1:00 position on your 7-way isn't active, you'll want to check the fuse in the power distribution box on the inside drivers side fender in the engine compartment. Remove the cover, and locate the two studs on the inboard side of the fuse block. The stud closest to the front of the truck should have a wire with a ring terminal fixed to it. If not, you'll...
  view full answer...
  
• Can The Curt C62VR Wiring Harness Be Used On A 2018 Jeep Grand Cherokee With Factory Tow Package
  Though it is perfectly fine to use the Curt # C62VR even if your 2018 Jeep Grand Cherokee has the factory towing package, I don't necessarily recommend it. Reason being, if your vehicle was set up with that package, it will have wires run that are specific to it. These tie into the vehicle's computers for diagnostics and other technical what have yous, but they are there to make life easier. Something like the Tekonsha # 118384 (whos harnesses I prefer due to them lasting longer) will plug...
  view full answer...
• No Trailer Lights After Installing T-One 4-Way Connector on a 2016 Jeep Grand Cherokee
  Wiring harness # 118384 is just a pass-through device. It is designed to work if your 2016 Jeep Grand Cherokee came with the factory-activated towing package. If the Jeep does not have the factory towing package you will need to have a Jeep dealer activate it for you. Otherwise the harness will not work. If your Jeep does have the factory tow package and it is indeed activated and the factory harness had power before you plugged in # 118384 then it is possible that in the process of installing...
  view full answer...
• How to Add a 4-Way to a 2008 Dodge Ram with 7-Way at the Rear of Vehicle
  The great thing about the ZCI trailer wiring harness part # 119250KIT is that it can be installed on basically any vehicle with taillights and it requires not splicing. Now that being said, if your truck has two 7-ways and you are looking for a way to also have a 4-way installed I have a better solution that would be much easier. For that you would want the part # 118384 which will give you a 4-way by plugging in line with the 7-way at the rear of your truck. I attached an install video...
  view full answer...
• Is Trailer Draw-Tite Trailer Hitch Visible When Installed On 2016 GMC Canyon
  I have attached a photo of the Draw-Tite Max-Frame Trailer Hitch Receiver, part # 76004 installed on a Canyon. Although it is not perfect, you can see that the receiver end is right under the rear bumper. Since the receiver sits below the horizontal bar on the hitch, it will be tucked up behind the bumper and much less visible than the Curt hitches. This is a Class lll hitch and it has a 2 inch receiver opening. If you plan on doing some towing you might be interested in etrailer ball...
  view full answer...
  
• What Typically Powers Lights and Fans in Horse Trailer Interior
  Most likely there's a battery somewhere in your trailer that is used to power the lights and fans. If it's an older trailer it's probably dead and would need to be replaced or charged. It's most likely up near the front of the trailer as well.
  view full answer...
  
• Fuse Locations for Trailer Running Lights on 2011 Ram 2500
  I took a look at the online version of the owner's manual for your 2011 Ram 2500 and found a couple of fuses you will want to check inside the power module located in the engine compartment. There should be a 40 amp green fuse located in the J01 position and a 20 amp blue fuse in the J14 position. Both of these fuses are related to trailer lights so you will want to check to make sure they are present and in good condition. If the fuses are good and you are having issues with the trailer...
  view full answer...
• Recommended Trailer Hitch For Ram 1500 With Factory Installed Crossmember
  The Draw Tite hitch part # 41948 is a confirmed fit for the 2017 Ram 1500. You will need to remove the factory hitch and install the Draw-Tite hitch. The maximum tongue weight is up to 1,500 lbs and the maximum gross trailer weight is up to 12,000 lbs. Another option is to use Draw-Tite Max-Frame Trailer Hitch Receiver # 75662. This receiver easily bolts on to your frame and does not require you to remove the factory crossmember. The maximum tongue weight is up to 600 lbs and the maximum...
  view full answer...

Do you have a question about this Custom Fit Vehicle Wiring?