Replacement Tail Panel Assembly for Extang Solid Fold 2.0 Hard Tonneau Cover

See what our Experts say about this Extang Accessories and Parts

• Replacement Hinge Installation on Extang Solid Fold 2.0 Hard Tonneau Cover
  The Extang Replacement Tail Hinge # EX83475-64 installs on the panels of their Solid Fold covers like 83475 by those panels' rounded edge rail sliding into the round channels on the hinge. The photo I linked shows the replacement hinge and these two channels. I confirmed with Extang that the round rail on the panels is not user-replaceable. If the panel on your cover has had its round edge rail break off then you will probably need to replace the panel. We do offer the Replacement Tail...
  view full answer...
  
• How Does Rear Panel of Extang Solid Fold 2.0 Install/Remove
  I spoke with my contact at Extang and they send me a set of install instructions that cover the installation and removal of the rear section of the Extang Solid Fold 2.0 which I attached to this page.
  view full answer...
  
• Replacing Panel on Extand Solid Fold 2.0 Hard Tonneau Cover
  To remove the rear hinge on the Extang Solid Fold 2.0 you'll need to check the end of the hinge rails for a small plastic cap; that cap can be removed and will expose a # 20 Torx screw. Once you remove that torx screw you'll be able to remove any panels on that hinge and replace them as needed. For a replacement panel on your Extang Solid Fold 2.0 you'll want to use the Replacement Tail Panel Assembly # EX83475-62 .
  view full answer...
• Extang Solid Fold 2.0 Tonneau Cover Hinge Seal Repair Instructions Written Out
  I found the picture you mentioned and while I wasn't able to find a better version that has easier to read text I can retype out the text of each step to make it easier to understand. Step 1. With the cover supported and laying flat, remove the three T20 Torx screws from the hinge and caps on one side. Step 2. With the panel angled at about 45 degrees slide it free of the hinge towards the missing end cap. Step 3. Rotate the hinge slightly and slide it free of the carrier panel. Repeat...
  view full answer...
  
• How to Install the Rear Panel on a Extang Solid Fold 2.0 Tonneau Cover
  If the rear panel on your Extang Solid Fold 2.0, like part # EX83475, came off and it is still in good condition then you can follow the instructions in the linked photo to reinstall it. If the rear panel is not in good condition then let me know the year/make/model of your pickup and I would be happy to let you know which replacement rear panel we have. For example, the part # EX83475 that I referenced is for a 2015 - 2019 Ford F-150 with a 5-1/2' bed or a 2017 - 2019 Ford F-150 Raptor...
  view full answer...
  
• Replacement Panel for Extrang Solid Fold 2.0 Tonneau Cover
  The rear panel (closest to the tailgate) is part # EX83475-62. This is a replacement panel and comes with instructions on how to remove the old panel and install the new panel. This will work on your Extang Solid Fold 2.0 83475. If your panel came off and is not damaged you can reattach it as long as everything is in working order.
  view full answer...
• Replacement Tail Panel Assembly For An Extang Solid Fold 2.0 On A 2015 GMC Sierra 3500 Long Bed
  The Replacement Tail Panel Assembly for Extang Solid Fold 2.0 Hard Tonneau Cover # EX83475-62 is designed to fit the Extang Solid Fold 2.0 Hard Tonneau Cover which is a fit for the 2015-2020 Ford F-150 & F-150 Raptor Short Bed trucks, and is not going to be a fit for your 2015 GMC Sierra 3500. Instead, what you're going to need is the Replacement Tail Panel Assembly for Extang Solid Fold 2.0 Hard Tonneau Cover # EX83445-62. I did go ahead and verify with Extang that this is the correct...
  view full answer...
• How Does Rear Panel of Extang Solid Fold Tonneau Cover Install
  I spoke with Extang a while back about basically your same question and they sent me the attached picture that covers the install of replacement tail panel for an Extang Solid Fold tonneau like with the kit part # EX83475-62 that you referenced.
  view full answer...
  
• Replacement Tail Hinge for Extang Solid Fold Tonneau Cover EX83475 Instructions
  I spoke with Extang a while back about basically your same question and they sent me the attached picture that covers the install of replacement tail panel for an Extang Solid Fold tonneau like with the kit part # EX83475-62.
  view full answer...
  
• Correct Replacement Tail Panel Assembly for an Extang Solid Fold 2.0
  Eric, the Replacement Corner Pads for Extang Trifecta Soft Tonneau Covers # EX4210 are designed to work with the Extang Trifecta tonneau covers so they're not going to work with your Solid Fold 2.0. From the looks of it, it appears that the corner pieces are not available separately for that cover. Instead you'd need to replace the entire tail panel # EX83475-62 to replace the damaged corners. If you can let me know what year, make, and model truck (including bed size) this cover is...
  view full answer...
• Rear extang Solid Fold 2.0 Panel Installation
  If you are having trouble with your etang Solid Fold 2.0 rear panel popping back into place them I recommend checking out the attached installation/ removal instructions. If you are following those instructions (installing it side-to-side) and you still cannot get it to work then it may be broken and in need of a replacement. If this is the case then I can help you with a replacement if you can get me the part number or the year/make/model of your truck.
  view full answer...
  
• Recommended Tonneau Cover To Replace Discontinued Extang Solid Fold 56450 That Is Damaged
  I have a complete replacement option for you, but unfortunately Extang discontinued the Extang Solid Fold Tonneau Cover 56450 you have on your 2014 Chevrolet Silverado back in 2015 and no replacement parts are available any longer. For a replacement cover I recommend going with the Extang Solid Fold 2.0 Hard Tonneau Cover # EX83450 which is a confirmed fit for your truck and is what replaced your current cover. I included a video review of the # EX83450 for you to take a look at.
  view full answer...
  
• How To Tell If Parts Are Missing From Rear Panel Extang Solid Fold Tonneau Cover That Blew Off Truck
  I have attached a page from the installation instructions for the Extang Solid Fold 2.0 Hard Tonneau Cover # EX83475-62. The page shows the parts that should be used with the rear panel you said blew off. You can look at the page to make sure all of the parts shown are still with the rear panel.
  view full answer...
  
• What Type Of Torx Screws Are Needed To Install Replacement Tail Panel For Extang Solid Fold 2.0?
  The Replacement Tail Panel Assembly for Extang Solid Fold 2.0 Hard Tonneau Cover # EX83475-62 uses T20 Torx screws, and will not use an Allen key.
  view full answer...
• Extang Rear Panel Replacement # EX83461-62
  Regarding the Extang # EX83475-62 replacement tail panel, I reached out to our contact at Extang regarding your question about the tube piece that slides into the hinge assembly. He described this "tube" as an arm that sticks into the hinge. The arm is included but the hinge is not. He also mentioned that when an end user asks about this part that it is usually an indication that there may be other damage that must be addressed to safely continue using the hard cover system as a whole....
  view full answer...
• Extang Replacement Hinge Recommendation for Trifecta 2.0
  The replacement hinge for the panels of the Extang Trifecta 2.0 is the hinge part # EX83645-64. Your picture didn't make it through but I attached a picture of what this hinge looks like installed. If you send me the picture you have I can check to see if anything else needs replacing.
  view full answer...
  
• Reinstalling Rear Panel On Extang Solid Fold 2.0 For Toyota Tundra
  To reinstall the rear panel on your Extang Solid Fold 2.0 you will first want to make sure is laying on a flat, supported surface. You will need to use a T-20 Torx Head bit to remove the screws holding the end cap to your cover. Next slide the panel onto the hinge from the side that you removed the end cap from. You will want to hold the panel at a 45 degree angle. With the panel reinstalled you will need reinstall the end cap. If you struggle to slide the panel back on, take a close...
  view full answer...
• Replacement Tail Panel For Extang Solid Fold 2.0 Hard Tonneau Cover
  We do have the replacement panel you need for your Extang Solid Fold 2.0 Hard Tonneau Cover, part # EX83475. The rear panel(closest to the tailgate) is part # EX83475-62. This is a replacement panel and comes with instructions on how to remove the old panel and install the new panel. This is a custom order so there is no returns allowed for this product.
  view full answer...
• Recommended Replacement Tonneau Covers For 2012 Toyota Tacoma With 6-Foot Bed
  I called my contact at Extang and they told me they no longer manufacture any of the part for the prior version of the Solid Fold 2.0. I asked if any parts were interchangeable and they told me they were not. I wish I had parts that woudl work for you but they just are not available. If you want to let me know the year make model and bed size you are looking for I will be glad to make some recommendations that will work for you.
  view full answer...
• Replacement Tail Hinge for Extang Solid Fold Tonneau Cover EX83475
  The hinge part of 83475 does not come with panel # EX83475-62. It is a separate part, # EX83475-64. Replacing the panel and hinge is not difficult though it may be easier with the cover off of the truck.
  view full answer...
• How to Uninstall/Reinstall the Replacement Tail Panel Assembly for an Extang Solid Fold 2.0
  I'm not quite sure what's happening but I can tell you for sure how to install the Replacement Tail Panel Assembly for Extang Solid Fold 2.0 Hard Tonneau Cover # EX83475-62 according to Extang. You're on track to start by removing the end caps on one side and sliding the old panel out. To replace it you'll just need to rotate the panel about 45° and slide it back into the place of the old panel. Finish by replacing the T20 Torx screws and endcaps. If you're still having trouble I'd suggest...
  view full answer...

Do you have a question about this Accessories and Part?