How Does Rear Panel of Extang Solid Fold 2.0 Install/Remove

Question

Question:

The rear panel of my extang solid fold 2.0 came off. I dont think anything broke. It looks like it just snaps back on. It is less than 2 months old. I have taken the cover off the F150 and tried to reattach the back panel to the middle one, but cant seem to snap it back into place. Any advice would be appreciated.

asked by: Destin

0

Expert Reply:

I spoke with my contact at Extang and they send me a set of install instructions that cover the installation and removal of the rear section of the Extang Solid Fold 2.0 which I attached to this page.

expert reply by: Jameson C

0

click to enlarge

Cody

4/24/2024

What size bit or Allen wrench do I need for the screws in the pockets

Reply

Jameson C.

4/25/2024

@Cody It's actually a T20 torx bit.

Reply

Answer 1

If the rear panel on your Extang Solid Fold 2.0, like part #EX83475, came off and it is still in good condition then you can follow the instructions in the linked photo to reinstall it. If the rear panel is not in good condition then let me know…

view full answer...

Answer 2

I found the picture you mentioned and while I wasn't able to find a better version that has easier to read text I can retype out the text of each step to make it easier to understand. Step 1. With the cover supported and laying flat, remove…

view full answer...

Answer 3

I have attached a page from the installation instructions for the Extang Solid Fold 2.0 Hard Tonneau Cover #EX83475-62. The page shows the parts that should be used with the rear panel you said blew off. You can look at the page to make sure all of…

view full answer...

Answer 4

The hinge part of 83475 does not come with panel #EX83475-62. It is a separate part, #EX83475-64. Replacing the panel and hinge is not difficult though it may be easier with the cover off of the truck.

view full answer...

Answer 5

To install/uninstall the panels on the Extang Solid Fold 2.0, you will need to remove the T20 Torx screws and hinge caps on one side. With the panel at a 45° angle, slide the panel towards the missing endcap. Then, rotate the hinge slightly and…

view full answer...

Answer 6

We do have the replacement panel you need for your Extang Solid Fold 2.0 Hard Tonneau Cover, part #EX83475. The rear panel(closest to the tailgate) is part #EX83475-62. This is a replacement panel and comes with instructions on how to remove the old…

view full answer...

Answer 7

The Extang Replacement Tail Hinge #EX83475-64 installs on the panels of their Solid Fold covers like 83475 by those panels' rounded edge rail sliding into the round channels on the hinge. The photo I linked shows the replacement hinge and these…

view full answer...

Answer 8

If you are having trouble with your etang Solid Fold 2.0 rear panel popping back into place them I recommend checking out the attached installation/ removal instructions. If you are following those instructions (installing it side-to-side) and you…

view full answer...

Answer 9

The Replacement Tail Panel Assembly for Extang Solid Fold 2.0 Hard Tonneau Cover #EX83475-62 uses T20 Torx screws, and will not use an Allen key.

view full answer...

Answer 10

I'm not quite sure what's happening but I can tell you for sure how to install the Replacement Tail Panel Assembly for Extang Solid Fold 2.0 Hard Tonneau Cover #EX83475-62 according to Extang. You're on track to start by removing the end…

view full answer...

Answer 11

If you do in fact have the Extang Solid Fold Hard Tonneau Cover #EX56430, which is no longer available, then the: -Replacement Hinge Seal for Extang Solid Fold 2.0 Tonneau Covers #EX32560669 will be the correct replacement hinge seal. Which makes me…

view full answer...

Answer 12

The Extang Replacement Tail Hinge #EX83475-64 installs on the panels of their Solid Fold covers like 83475 by those panels' rounded edge rail sliding into the round channels on the hinge. The photo I linked shows the replacement hinge and these…

view full answer...

How Does Rear Panel of Extang Solid Fold 2.0 Install/Remove

Product Page this Question was Asked From

Continue Researching