What Type Of Torx Screws Are Needed To Install Replacement Tail Panel For Extang Solid Fold 2.0?

Question

Question:

What size and type of tool to remove the screw on my Solid Fold 2.0? Torx screws type? Allen Key?

asked by: John D

0

Expert Reply:

The Replacement Tail Panel Assembly for Extang Solid Fold 2.0 Hard Tonneau Cover # EX83475-62 uses T20 Torx screws, and will not use an Allen key.

expert reply by: Bryce D

0

Answer 1

I spoke with my contact at Extang and they send me a set of install instructions that cover the installation and removal of the rear section of the Extang Solid Fold 2.0 which I attached to this page.

view full answer...

Answer 2

We do have the replacement panel you need for your Extang Solid Fold 2.0 Hard Tonneau Cover, part #EX83475. The rear panel(closest to the tailgate) is part #EX83475-62. This is a replacement panel and comes with instructions on how to remove the old…

view full answer...

Answer 3

If the rear panel on your Extang Solid Fold 2.0, like part #EX83475, came off and it is still in good condition then you can follow the instructions in the linked photo to reinstall it. If the rear panel is not in good condition then let me know the…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 6

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 9

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

In order to match up the wheel studs for your Reliable 1206 hub, we'll need to know the full dimensions of the wheel stud you're replacing. In addition to the total length of the stud and its diameter and thread pitch, we'll also need to…

view full answer...

Answer 12

I added a photo which shows the location of the heating element of the Atwood Water Heater GC6AA-10E for you. It is item number 17 in the diagram. Atwood does recommend having a professional do the job if you are replacing it due to its location.

view full answer...

What Type Of Torx Screws Are Needed To Install Replacement Tail Panel For Extang Solid Fold 2.0?

Product Page this Question was Asked From

Continue Researching