Replacement Tail Panel For Extang Solid Fold 2.0 Hard Tonneau Cover

Question

Question:

If the back panel is broken can just that panel be replaced or do you have to buy a whole new cover?

asked by: Debbie

0

Expert Reply:

We do have the replacement panel you need for your Extang Solid Fold 2.0 Hard Tonneau Cover, part # EX83475.

The rear panel(closest to the tailgate) is part # EX83475-62. This is a replacement panel and comes with instructions on how to remove the old panel and install the new panel. This is a custom order so there is no returns allowed for this product.

expert reply by: Jeffrey L

0

Answer 1

If the rear panel on your Extang Solid Fold 2.0, like part #EX83475, came off and it is still in good condition then you can follow the instructions in the linked photo to reinstall it. If the rear panel is not in good condition then let me know the…

view full answer...

Answer 2

I spoke with my contact at Extang and they send me a set of install instructions that cover the installation and removal of the rear section of the Extang Solid Fold 2.0 which I attached to this page.

view full answer...

Answer 3

The hinge part of 83475 does not come with panel #EX83475-62. It is a separate part, #EX83475-64. Replacing the panel and hinge is not difficult though it may be easier with the cover off of the truck.

view full answer...

Answer 4

The Replacement Tail Panel Assembly for Extang Solid Fold 2.0 Hard Tonneau Cover #EX83475-62 uses T20 Torx screws, and will not use an Allen key.

view full answer...

Answer 5

The Extang Replacement Tail Hinge #EX83475-64 installs on the panels of their Solid Fold covers like 83475 by those panels' rounded edge rail sliding into the round channels on the hinge. The photo I linked shows the replacement hinge and these…

view full answer...

Answer 6

If you are having trouble with your etang Solid Fold 2.0 rear panel popping back into place them I recommend checking out the attached installation/ removal instructions. If you are following those instructions (installing it side-to-side) and you…

view full answer...

Answer 7

The Extang Replacement Tail Hinge #EX83475-64 installs on the panels of their Solid Fold covers like 83475 by those panels' rounded edge rail sliding into the round channels on the hinge. The photo I linked shows the replacement hinge and these…

view full answer...

Answer 8

If you have the Extang Solid Fold 2.0 like the Extang Solid Fold 2.0 Hard Tonneau Cover - Folding - Polypropylene #EX83801 you linked to then you would need the following parts. Replacement Tailgate Seal for Extang Solid Fold 2.0 Tonneau Covers…

view full answer...

Answer 9

If you do in fact have the Extang Solid Fold Hard Tonneau Cover #EX56430, which is no longer available, then the: -Replacement Hinge Seal for Extang Solid Fold 2.0 Tonneau Covers #EX32560669 will be the correct replacement hinge seal. Which makes me…

view full answer...

Answer 10

I found the picture you mentioned and while I wasn't able to find a better version that has easier to read text I can retype out the text of each step to make it easier to understand. Step 1. With the cover supported and laying flat, remove the…

view full answer...

Answer 11

I have attached a page from the installation instructions for the Extang Solid Fold 2.0 Hard Tonneau Cover #EX83475-62. The page shows the parts that should be used with the rear panel you said blew off. You can look at the page to make sure all of…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Tail Panel For Extang Solid Fold 2.0 Hard Tonneau Cover

Products Referenced in This Question

Continue Researching