You will need the Firestone Ride-Rite Air Helper Springs # F2558 for your 2016 Nissan Frontier. You will not need any spacers as the Rough Country 2.5" leveling kit only provides lift to the front suspension.
The Air Lift WirelessAIR Compressor System # AL58WQ will allow you to control the air pressure with your smart phone and the Air Lift app. The smart manifold will monitor the air pressure while you drive and make adjustments to the air pressure if it changes by more than 3psi. It... view full answer...
WeatherTech currently only carries a tailgate liner for a 2022 Nissan Frontier with a 6' bed so the only other option I currently have is the Access Custom Truck Bed Mat # A45BG. This half inch thick carpet easily snaps in and out of place so that you can protect your bed or pull the mat out to clean it.
WeatherTech does carry a tailgate liner # WT42XQ if you're looking for tailgate protection as well. view full answer...
On your 2019 Nissan Frontier that came with the factory harness, you will only need to plug in the Hopkins Plug-In Simple Vehicle Wiring Harness # HM43534 once. Then when you need to use the towing connections you will just plug into either the 4-way flat or 7-way blade connectors.
Some Dielectric Grease # 11755 is recommend on the connectors to protect against corrosion and other wiring issues. view full answer...
For your 2008 Nissan Titan, I would suggest the Reese Semi-Custom Install kit, part # RP30035-405. This kit has all the hardware you will need to get the truck set up for a traditional bed rail fifth wheel hitch. I have added links to the instructions as well.
Reese 16K Fifth Wheel, part # RP30051 is a fifth wheel equipped with a slider, which you will not need since you have a full 8 foot bed. Instead I would recommend Reese part # RP30047. It is the same as 30051 but without the sliders.... view full answer...
Draw Tite and Curt/etrailer rate their hitches independently from one another which is why it's often that the hitches will be rated for different capacities. This is why the Draw Tite hitch part # 75952 is rated higher than your 2018 Nissan Murano.
The overall towing capacity is always the lowest rated component in the setup as you are only as strong as your weakest component. view full answer...
The pilot diameter of the trailer wheel part # AM22627 is 3.19 inch so you'd need a center cap like part # 319EZ. For locking lug nuts you'd want part # RG01-150 or for standard lugs # LHLR103. view full answer...
I have a possible solution for you, but none of the tailgate-lowering systems with shock absorbers will work with your 2018 Nissan Frontier. You may be able to use the Hopkins EasyLift Truck Bed Tailgate Lift Assist # 74211, but this also has not been confirmed to fit your vehicle so I cannot say for sure if this will work. It uses a single torsion bar to make lifting and lowering the tailgate easier. I recommend looking at the demonstration video I attached along with the photos on the... view full answer...
As long as you have room for the # PK-28WL2-BM you won't have a problem mounting it on your 2017 Nissan NV 3500. The rack has a tower height of 46-3/4". Considering the fact that someone mounted this on their NV 2500 I don't think you will have an issue, see the attached picture below. view full answer...
So long as you have a smart phone capable of downloading Curt's app the Curt Echo Wireless Brake Controller item # C51180 will definitely work with your Pathfinder's 7-way harness. The 12v line on your Nissan's 7-way will function and charge your trailer's battery. This is the best option for wireless brake controllers.
I have linked an installation video below so you can see how to set up the Curt Echo. view full answer...
When we installed the Draw-Tite # 76031 and Curt # C13309 trailer hitch receivers on a 2018 Nissan Pathfinder - which is the same body as a 2019 Pathfinder - we found that the Draw-Tite had both better ground clearance and better bumper clearance.
The Curt measured 14 inches from the ground to the top of the hitch with 5 inches from the hitch pin hole to the end of the bumper, while the Draw-Tite measured 14-1/2 inches from the ground and 4 inches from pin hole to the end of the bumper.
Due... view full answer...
I recommend the Equal-i-zer Weight Distribution System # EQ37060ET over the Reese Steadi-Flex # RP66558 for your 2021 Geo Pro. This hitch is rated for a maximum trailer weight of 6,000lbs which the Geo Pro is well under. The tongue weight needs to be between 200-600lbs and you are right in the middle at 419lbs.
The Sway Bracket Jackets for Equal-i-zer Weight Distribution Systems # EQ95-01-5150 can be used with the hitch to reduce the noise the hitch produces when maneuvering your trailer.... view full answer...
Your ebikes weight is one of the limiting factors in carrying them on the roof of your vehicle. The Yakima ForkLift Roof Mounted Bike Carrier - Fork Mount, part # Y02098, has a weight limit of 40lbs. But if your roof rack has crossbars with a channel my recommendation would be the Inno Fork Lock Roof Bike Rack - Fork Mount - Channel Mounted - Aluminum, part # INXA391.
It is a fork mounted rack that attaches to the channel of your crossbars. It has a weight limit of 50lbs and locks your... view full answer...
The Draw Tite hitch part # DT23MR that you referenced is a confirmed fit for your 2021 Nissan Rogue and also is compatible with the hands free liftgate you have as well. Basically you'd just have to kick to either side of the hitch opening and you'd be set. view full answer...
For your Magic Tilt Boat Trailer you will need a Blue Ox Pole Tongue Weight Distributing Hitch Adapter # BXW4023. This will bolt around the Pole frame with a width of 2-3/4" to 4-1/2" and height of 3" to 6". It will then allow you to use a weight distribution hitch that utilizes over frame brackets.
I recommend the Blue Ox SwayPro Weight Distribution w/ Sway Control # BXW0556. This system will allow you to back up your boat trailer without removal and will not interfere with the surge... view full answer...
Although we do have towing mirror options for your 2013 Nissan Xterra, a custom slip-on mirror like the
# CM10900 you'd looked at isn't available.
I'd recommend the K-Source Universal Towing Mirrors, part # KS3891-2. These mirrors attach to the factory mirrors using sturdy ratcheting straps that provide a tight fit for minimal vibration. The 7-3/4 x 5-1/8 mirrors provide a great field of vision when towing. The driver and passenger side mirror are included.
If you click the provided... view full answer...
If you have two vents, you are correct that you would need to order two of the Valterra Bug Screens for Dometic RV Refrigerator Vents # A10-1311VP. view full answer...
We have the aluminum Erickson Truck Bed Ladder Rack part # EM07705 that is a confirmed fit for your 2019 Nissan Frontier King Cab 6 ft bed with the Utili Track.
I attached a review video for this rack for more info for you to check out as well. view full answer...
The Westin HDX Grille Guard with Punch Plate # 57-3915 will interfere with the front sensors and camera on your 2016 Nissan Titan XD Pro 4X. This is true for all of the available grille guards. If you do decide to buy it and install it I recommend checking with your local Nissan dealer to see if it is possible to relocate them. Sometimes they make relocation kits, at least for the sensors. view full answer...
I recommend using the Brophy Rope D-Ring Tie-Down Anchor # BR59FR on your 2019 Nissan NV200 SV. This D-Ring has a large plate that will provide a more stable mount and allow you to more easily slide large objects over the rings with less chance of catching. You will want to use the Backing Plate # BP12 if you are not mounting into solid steel framing. Each D-Ring is rated for a working load limit of 500lbs. view full answer...
The RetraxONE XR Hard Tonneau Cover part # RTT-60421 is my recommendation for a 2007 GMC Sierra 1500 New Body Style with 5-1/2' Bed. This is a hard, retractable tonneau cover which has t-solt rails on the outside so you can mount a rack like the Yakima OverHaul HD Adjustable Truck Bed Ladder Rack for Tonneau Cover part # Y01151-5955. It locks so you can keep your bed content safe and it's made here in the USA. view full answer...