The largest portable toilet seat that we carry is the Dometic Portable Camping Seat which has a 5 gallon tank and comes with a Gray Base # DOM44FR.
The seat itself is 13-1/4" long and the cutout is 8-3/4" x 7-1/4". According to my research it is regularly among the top picks for portable toilets in 2020. view full answer...
The SumoSprings Solo Custom Helper Springs for a 2023 Nissan Frontier, part # SS46EV for a 1,800 lb capacity and part # SS96EV for a 1,400 lb capacity, measure 4" tall and they come with a 1/2" spacer. You'll want to shoot for about a 1" gap between the jounce spring and leaf springs. If you don't want them to engage as much you can omit the spacer.
Please note, the capacity of the spring correlates to tongue weight and or payload, the closer the capacity of the load to the spring, the... view full answer...
The Draw-Tite Sportframe Trailer Hitch Receiver # 24788 is a Class I, 1-1/4 inch hitch that has a maximum tongue weight capacity of 200 pounds. This means the weight of a cargo carrier and whatever is on the carrier will have to no more than 200 pounds.
I found an owner's manual online for your 2005 Nissan Altima and it states the the vehicle's maximum tongue weight is 100 pounds. Check your owner's manual to be sure because you will be limited by the lowest rated factor. The Draw-Tite... view full answer...
The power wire of the Tow Ready Custom Wiring Kit # 118480 that you referenced is 12 gauge.
I attached an install video, installation instructions and an FAQ article on routing power wires for converters like this for you to check out also. view full answer...
To answer your questions in order:
1)Yes, you will be able to use the Kuat Transfer 3 with the 2" hitch receiver on the EcoHitch Hidden Hitch # 306-X7221 . The Transfer 3 is a great choice for carbon frame bikes because of the ratcheting wheel mounts that make zero contact with your bike frame.
2) The discrepancy on the tongue weight of the hitch is likely down to a weight capacity upgrade made by EcoHitch after the hitch was released-rarely are the instructions updated. I checked with... view full answer...
I took a look at the online owner's manual for your 2008 Nissan Frontier and it stated that you can use your bumper hitch and a hitch ball to tow up to 3,500 lbs. So as long as your trailer's total capacity is under that you can tow with your Frontier.
You will also need a 4-way to connect your trailer's lights if you do not already have one. The Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56225 will be exactly what you need and I've also added a link... view full answer...
No, you won't have to modify the Util-Track system to install the Lomax Hard Tonneau Cover item # LOM66QR. The rails for the tonneau cover mount about the track system on your 2017 Nissan Titan. I have linked the instructions below so you can see the process. view full answer...
The inside to inside flange to flange distance of the # DT85MR Draw-Tite Class III hitch is 44 inches. Each mounting flange has 3 holes, the center hole is 2.87 inches from the mounting hole closest to the receiver tube, and the center hole and the forward-most hole are 6.59 inches apart. The hole spacing dimensioned are measured center to center. I've provided a photo showing these dimensions.
The # DT85MR is a confirmed fit for the 2021 Nissan Rogue. If you'll be using the hitch for... view full answer...
The Malone Runway Bike Rack # MPG2130 has 2 hitch pin locations to allow you to determine which will best fit your 2014 Nissan Rogue. From the first center hitch pin to upright bar is 7-3/8". The second center hitch pin to upright bar is 9-3/8"
The etrailer Trailer Hitch Receiver # e98846 has a 4-1/2" hitch pin center hole to bumper measurement on your Rogue. So you will have either a 2-7/8" or 4-7/8" clearance from the bumper to the upright bar on the Malone rack.
I recommend securing... view full answer...
The price of the etrailer # e65AR that fits your 2013 Nissan Murano can be found on the liked product page. Please note that this hitch fits all models of the '13 Murano with the exception of the CrossCabriolet. It is a 2 inch hitch with a 4,000 lb towing capacity and 400 lb tongue weight capacity. I've added a link to a video review of this hitch being installed on a 2013 Murano for you to take a look at.
If you need to add wiring to power your trailer's lights you will need the T-One... view full answer...
Yes, there are. To add a front mount hitch to your 2019 Nissan Frontier you're going to want the Curt item # 31241. This front mount hitch has a 2" receiver and bolts to your Frontier with included hardware. This hitch has a line pull capacity of 9,000 lbs, a vertical load limit of 350 lbs, and it can pull a trailer weighing up to 3,500 lbs.
I really like this hitch because it mounts directly below the front fascia. I have linked an installation video below along with a couple of pictures... view full answer...
The AirBedz XUV Air Mattress # 341030 that you referenced measures 52" wide at the widest section and 43" wide for the shorter width (see attached photo). This is a confirmed fit for your 2002 Nissan Xterra. view full answer...
The hub bore of Trailer Hub and Drum Assembly # AKHD-655-35-K is 1.980-inches and this allows a good fit with a grease cap like # F001518 which has a flange diameter of 1.988-inches. view full answer...
The Draw-Tite Max-Frame Trailer Hitch Receiver # 75282 will have the following bolt hole dimensions for your 2015 Nissan Frontier.
The Bolt holes from drivers side to passenger side frame rails are 43-5/8" on center. The holes running from front of the hitch to back are spaced 3-1/2" on center. I have included the picture with measurements for you to reference. view full answer...
Your ebikes weight is one of the limiting factors in carrying them on the roof of your vehicle. The Yakima ForkLift Roof Mounted Bike Carrier - Fork Mount, part # Y02098, has a weight limit of 40lbs. But if your roof rack has crossbars with a channel my recommendation would be the Inno Fork Lock Roof Bike Rack - Fork Mount - Channel Mounted - Aluminum, part # INXA391.
It is a fork mounted rack that attaches to the channel of your crossbars. It has a weight limit of 50lbs and locks your... view full answer...
The Curt Front Mount Hitch, # 31514, has a 9,000 lbs. maximum line pull. That is the gross load capacity when used as a straight line pull.
Straight line pull means that the winch cable must not exceed 15 degree angle up or down from horizontal or 45 degree angle left or right from straight ahead.
So the hitch will be strong enough to winch your Nissan Xterra.
I am sending a link to the instructions on the Curt front hitch which will show the installation and some information on winching... view full answer...