Customers compare MCL48AB to these similar products
Products Featured in this Video
Today we're going to be taking a look at part number MCL48AB. This is the Optronics micro-flex LED amber side marker light. The amber PC-rated light is going to function as both clearance and side marker light, as well as mid-ship turn signal. The light must be mounted at a 45-degree angle. LEDs are great replacements for incandescent lights. They last a lot longer, they're much more efficient.… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
The overall dimensions I'm seeing for the Dometic RM7732 show it being 59-5/8" tall x 33-9/16" wide x 25-15/16" deep. While we won't have a prefect fit we do have the Everchill RV Refrigerator w/ Freezer #324-000119, which can…
view full answer...You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…
view full answer...The Chevy Vans are not actually pre-wired for a brake controller. A brake controller has to be partially hardwired in. If your 2007 Chevy Express came with a factory installed 7-Way trailer connector then the blue brake output wire should be ran from…
view full answer...Per Bullring's fitment guide the Bullring Truck Bed Side Wall Anchors for Corner Pockets #BU44FR fit 2019+ models in the front corners only, but will not fit if you have the corner bracket I have pictured below.
view full answer...Yes, there is a flush fit BullRing Tie-Down for your 2022 Ram 1500. You can get them in a set of two or four and with a gunmetal or a stainless steel finish. If you need a set of two of the Replacement BullRing Retractable Tie-Down Anchors for Truck…
view full answer...The best way to power the interior lights in your trailer is with its own independent battery. You will not want to use the breakaway battery. The breakaway battery is only designed to operate the breakaway and will drain extremely quickly,…
view full answer...Trailers use what is called a 2-wire system which means the turn signals and brake lights are on the same circuit. When you try to add separate amber turn signals you will need to separate out the brake light signal using a converter, #118158. On…
view full answer...The Trailer Clearance and Side Marker Light #MCL48AB uses a three wire setup which means that the light has two light intensities. A lower intensity for the running light circuit and a brighter intensity that will come on when the brakes or turn…
view full answer...The mounting holes are 2 inches apart, and to ensure its full capacity we do recommend screws in every mounting hole for the Erickson Horizontal E-Track #EM19147. While we do not have the mounting hardware, the mounting holes are 1/4" diameter,…
view full answer...When installing the etrailer Horizontal E-Track part #e65VR we generally use a rubber material that is generally used as a liner in garden ponds. It is easy to cut into strips and place under the full length of the track. Once secured down we trim…
view full answer...The E-Track has slots that have a length of 2.45-inches and a width of .58 inches. See attached diagram. I couldn't find any information on the ANCOR brand so you would need to compare what you have to those dimensions to know if the accessories…
view full answer...Yes, you are absolutely correct. To wire up the Miro-Flex LED Trailer Side Marker Light #MCL48AB to work as a blinker and running light you would need to run the stop/turn signal wires to the red wires, the running lights to the black wires and the…
view full answer...