Customers compare FA92-02-1099 to these similar products
Products Featured in this Video
Hi there, I'm Michael with etrailer.com. Today, we're gonna take a quick look at this Fastway Replacement Trunnion Spring Bar. So, if you already have the Fastway e2 weight-distribution system and you're needing a higher tongue weight, whether you're upgrading to a different trailer or if you're just putting more weight in your trailer than you originally planned, this is gonna be a great way to… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
The weight capacity of the 600 lbs Spring Bars is: tongue weight: 250 lbs - 600 lbs; gross towing weight: 6,000 lbs. If the tongue weight on your trailer is 600 lbs when empty, I would recommend increasing the weight capacity. I would recommend…
view full answer...The square tubes are different sizes. The systems basically have two bar dimensions, so if you bars are a fit in the head, then you will be fine with the head. If the bars do not fit in the head, then you cannot make it compatible. There are two…
view full answer...The Fastway e2 weight distribution (WD) 8,000 lb and 10,000 lb systems do use the same head units so you can easily use the 1,000 lb Trunnion Bars #FA92-01-1099 or 2 of the Rounds Bar #FA94-02-1099 with your current setup depending on which you have.…
view full answer...For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…
view full answer...The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
view full answer...You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…
view full answer...Hey Travis, congrats on the new 2024 Jayco Flight 284BHS! Your travel trailer looks to have a GVWR of 7,950 lbs so I recommend going with the Equal-i-zer Weight Distribution w/ 4-Point Sway Control #EQ37121ET and pairing it with the Shank…
view full answer...The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…
view full answer...A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
view full answer...Hi Joe, Yep, you heard correct, you can go from a 2 inch shank to a 2-1/2 inch shank with your Reese weight distribution hitch without issue. One of the following 2-1/2 inch shanks should have the right rise/drop for your application. Here are the…
view full answer...In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
view full answer...Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…
view full answer...