Customers compare CAM59153 to these similar products
Products Featured in this Video
Today we're going to be taking a look at the Camco Propane Supply Hose. This is a 24-inch pigtail supply hose that lets you connect an auxiliary propane cylinder to your RV or trailer's propane regulator. It's going to feature a type one Acme nut at one end that connects an Acme or POL connection on your propane tank. On the other end it's going to feature the quarter-inch inverted male flare.… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
For the MB Sturgis Sturgi-Stay T-Fitting w/ Hose for POL Valve - 2 Model 250 Quick Disconnect Ports #103538-MBS you will put this between the tank and the motorhome's in line regulator. Then you will need a single stage regulator like #CAM59013…
view full answer...It looks like there is 3/8" NPT fitting attached to the regulator on your propane tank like hose #100040-48-MBS which has a 3/8" female flare fitting on the other end. Based on that MB Sturgis Sturgi-Stay T-Fitting #103538-MBS would not…
view full answer...What you need is a T-Fitting and auxiliary hose like what comes in the Kit #103538-MBS, but your propane setup is a bit different than a normal RV so you'll need to get creative in how you're able to connect the T-Fitting. One end is a male…
view full answer...Thank you for the photo it was helpful, and what it shows is you do have the standard dual propane tank set up, so you can absolutely use the MB Sturgis regulator you asked about: - MB Sturgis High Capacity Two-Stage Auto Changeover Regulator…
view full answer...Fitting #CAM59953 is designed to connect a 1/4 inch inverted flare to a 1/4 inch female NPT. The one end is a 1/4 inch male NPT and the other is a 1/4 inch female inverted flare fitting. It sounds like you need one that does the opposite but we do…
view full answer...The Replacement Check Valve/Vacuum Breaker for Factory RV Tank Flushing Systems part #A10-3050 can be used on either black or grey water holding tanks to protect fresh water supply from contamination. I have attached a photo for you which shows how…
view full answer...Yes, you can use a regular hose clamp so your hose has a better connection to the Check Valve/Vacuum Breaker #A10-3050. The thing you need to watch out for though is that you don't tighten the clamp too hard and break the connector the hose is…
view full answer...The Replacement Check Valve/Vacuum Breaker #A10-3050 matches what you currently have only it is constructed of clear plastic rather than the black plastic.
view full answer...I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…
view full answer...When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…
view full answer...To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...