Recommended Trailer Brake Controller for Use in 1984 Chevrolet K20 Pickup

Question

Question:

I have a1984 chevy k20 pu and I want to wire it up for electric brakes what do I need as well as getting good instructions

asked by: Steve

0

Expert Reply:

To install a trailer brake controller in your 1984 Chevrolet K20 Pickup you will need the brake controller itself, such as the excellent Tekonsha Primus IQ # TK90160 that you referenced, as well as a brake controller installation kit # ETBC7. If your truck does not already have a working 4-pole flat trailer connector you will also need one those, part # 118311.

Your installation will be a hard-wire type since there is no quick-connect port under the dash. At right you will find links to a video and articles concerning installation of the # ETBC7. These will give you step by step guidance for the installation.

expert reply by: Adam R

0

James L.

4/13/2020

I have a 86 chevy 1ton k30 military pick up. I need all hardware and wiring for electric trailer brake.

Reply

Chris R.

4/14/2020

If you don't yet have a trailer connector on your K30 you'll need to start with a 4-Way, the Tekonsha # 118312. From there you can upgrade it to a fully functional 7-Way using the Wiring Kit # ETBC7 that Adam mentioned above. I like his recommendation of the Primus IQ # TK90160 as well. This will give you everything you need.

Reply

Answer 1

I recommend the Tekonsha Prodigy P3 Trailer Brake Controller #90195 for your 1984 Chevrolet K30 pickup. The P3 is a proportional brake controller that will adjust the brake force sent to the trailer for light and heavy braking. It can work on…

view full answer...

Answer 2

I contacted our representative at Tekonsha about installing the Tekonsha Prodigy P3 Trailer Brake Controller part #90150 on your vehicle with 24 volt system. There is actually a technical bulletin on how to install a brake controller on a 24 volt…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

I do have a solution for your 2024 Kia Telluride that has the LED taillights that does allow it to have both a 4-way and 7-way plus install a brake controller but it is not with the #TK74CR which does not work for you based on the LED taillights.…

view full answer...

Answer 11

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 12

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...