Husky Brute Powered Jack Recommendation

Question

Question:

On the Pro Series - 5000 lb. Lift, side winding. Is there a 12V motor available for that jack?

asked by: Robert K

0

Expert Reply:

There isn't a motor available for the Pro Series Square Jack # PS1400850383, but what you might be interested in would be a powered jack like the Stromberg Carlson # SC63VR electric tongue jack.

This is an A-frame jack with a 4,500 lb capacity that would work well as long as you have an A-frame jack and a tongue weight less than 4,500 lbs. It also has a clutch that prevents damage from over extending or retracting it. Additionally, a resetable breaker should the jack draw too much amperage.

expert reply by: Jameson C

0

Answer 1

We do have some smaller heater pads such as #277-000161 at 13 x 3 inches or #277-000162 at 8 x 3 inches. The larger one draws 0.62 amps at 13.5 volts. The smaller one draws 0.3 amps at 13.5 volts.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The newer factory brake controllers, like on your 2022 Chevy Silverado, are generally fine with an EOH actuator like the Dexter DX Series Electric Over Hydraulic Brake Actuator #K71-651. But there are times when there are issues which is why I…

view full answer...

Answer 6

Interesting. We don't have that specifically, but there are a couple of routes you could go. Most trailers will use the Scissor Stabilizer Jack - 18-3/4" Travel - 2,500 lbs - Qty 1 #TJSC-24 for stability in the corners so you could mount a…

view full answer...

Answer 7

The distance between the mounting holes is going to be the same between each one, or between each set. Center on center, they're going to be separated by 3 inches and the mounting holes are going to have a diameter of 1/2 inch. The channel width…

view full answer...

Answer 8

The only option to add a jack to your trailer with that tongue would be to drill in and attach it to the front of the trailer itself. You could use the Round Swivel Marine Jack w/ Wheel #MJ-1206B and bolt it straight onto the frame instead of using…

view full answer...

Answer 9

The Dutton-Lainson Square Swivel Jack #DL22340 has a mounting plate designed to fit trailer frames with a height of 3" - 5". I have attached a dimensional drawing below with all of the bolt spacing for your reference.

view full answer...

Answer 10

Absolutely. Trailer jack #PS1400850383 was designed to be welded on to a trailer frame so you made an excellent choice. Any welding should be performed by a qualified professional welder. I have included a link to a video review of this jack for…

view full answer...

Answer 11

Since your hub uses inner bearing #L68149 and outer bearing #L44649 you can use the Bearing Buddy Bearing Protector Stainless Steel #BB1980A-SS that you were looking at or the Chrome Plated #BB1980A. I included videos for both of the products…

view full answer...