Measurements on the Channel Tongue Trailer Coupler
Question:
How far are the bolt holes apart, centre to centre, for the CT-3002-Z Ram Straight Channel Tongue Trailer Coupler
asked by: Peter
1
Helpful Expert Reply:
The distance between the mounting holes is going to be the same between each one, or between each set. Center on center, they're going to be separated by 3 inches and the mounting holes are going to have a diameter of 1/2 inch. The channel width on the unit, inside edge to inside edge measures 2-1/2 inches.
expert reply by:
Timothy G
1
Product Page this Question was Asked From
Channel Tongue Trailer Coupler - Trigger Latch - Zinc - 2" Ball - Bolt On - 3,500 lbs
- Straight Tongue Trailer Coupler
- Standard Coupler
- 2 Inch Ball Coupler
- Bolt-On
- 3500 lbs GTW
- 2-1/2 Inch Channel
- Trigger Latch
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Square Direct Weld Jack w/ Footplate - Drop Leg - Sidewind - 28-3/4" Lift - 3,000 lbs
- Shop: Leveling Scissor Jack Set - 30" Lift - 10,000 lbs - QTY 2
- Shop: Channel Tongue Trailer Coupler - Trigger Latch - Zinc - 2" Ball - Bolt On - 3,500 lbs
- Q&A: Outside Diameter of Deka Wire - Jacketed 6-Wire - per Foot
- Shop: Curt QuickPin No-Latch Trailer Coupler for 2" Ball - 3" Channel - 3,500 lbs
- Video: Review of Stromberg Carlson Camper Jacks - Leveling Stabilizer Jacks 10K - JSC-30
- Q&A: Brainstorming Sidewind Trailer Jack for 2 Inch Receivers On Cargo Trailer Corners For Stabilization
- Q&A: Trailer Jack for Trailer With Non-Traditional Trailer Tongue
- Shop: Tool Box
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Wiring Trailer Lights with a 5-Way Plug (It's Easier Than You Think)
- Article: Trailer Wiring Diagrams
- Q&A: How Long Is The Channel Opening On The Demco Channel Tongue Trailer Coupler # DM15629-52?
- Article: Where to Position the Trailer Axle?
- Video: Review of Curt Straight Tongue Trailer Coupler - Standard Coupler - C54UR
- Shop: Kenda ST225/75R15 Radial Tire with 15" Aluminum Wheel - 6 on 5-1/2" - LR E
- Shop: Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles - 5 on 5 - Pre-Greased
- Shop: Bearing Kit, L44649 Inner/Outer Bearings, 10-9 Seal
- Q&A: Difference Between an Idler Hub and a Hub/Drum
- Q&A: Replacement Trailer Hub Assemblies For 3,500LB Axles Using L68149 Inner and L44649 Outer Bearings
- Video: etrailer Trailer Bearings Races Seals Caps - Races - L68111 Review
- Video: Review of Demco Straight Tongue Trailer Coupler - Standard Coupler - DM15629-52
- Q&A: How to Determine the Correct Axle Position When Building a Trailer
- Search Results: wire terminals
- Search Results: boat buckle
- Search Results: quick coupler
- Search Results: identification light bar
- Search Results: cargobuckle
- Search Results: cargo straps
- Search Results: wiring conduit