Which Optronic Replacement Marker Lights will fit in the Optronics Chrome Trailer Light Bracket

Question

Question:

Will the MC66RB and MC66AB fit in the BK-42CB bracket? I need to replace some broken marker lights and brackets. The BK-42CB chrome bracket looks like what I have on my trailer, but your listing mentions it is for the Double Bullseye Clearance lights MC42RB and MC42AB. The other lights on my trailer are not the double bull's-eye.

asked by: Josh B

0

Expert Reply:

Double Bull's-eye LED Trailer Clearance and Side Marker Light # MCL45AB and # MCL45RB will fit with Chrome Trailer Light Bracket # BK42CB. These two lights will be a little tighter fit.

Double Bull's-eye Trailer Clearance, Side Marker Light # MC42RB and # MC42AB will also work with # BK42CB.

I have linked a video for you as well.

expert reply by: Chris B

0

Answer 1

We have a version of the #MCL95AB in red with the part #MCL95RB.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 4

Since Grand Design is kind enough to list certain parts for their trailers I can confirm you have a 33" wheelbase on your 2020 Grand Design Transcend 27BHS. This means the MORryde Rubber Equalizers #MR87ZR will fit your trailer. Although I'm…

view full answer...

Answer 5

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 6

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 7

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 10

It is possible to replace your 62" long axle with a longer one. Our next size up is going to be a 72" long 2K rated axle like part #e32GR. The axle being 72" across measured from hub-face to hub-face. This axle comes with 5 on…

view full answer...

Answer 11

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...

Answer 12

I spoke to Dexter and they said there is a bit of a process for installing the spindle nut properly. 1. You will need to thread on the inner nut, rotate the hub, then tighten the nut to 100 foot pounds. 2. Loosen the nut to remove the torque, making…

view full answer...