Will Curt Trailer Hitch 15302 Fit a 2002 GMC Sierra 2500HD with 6-1/2 Foot Bed

Question

Question:

Hi, will this fit a 2002 GMC2500HD with 6 1/2ft. bed? I want to make sure before I buy. thanks

asked by: Randy

0

Expert Reply:

Yes indeed. You can install Curt trailer hitch # C15302 on your 2002 GMC Sierra 2500HD short bed. I also recommend etrailer ball mount kit # EBMK2416. It comes with a ball mount, 2 balls, a hitch pin with clip, and a storage bag.

And if you need to add a trailer connector you can use # HM40975 which has both a 7-Way and 4-Way. I have included a link to a video that shows how it installs on a similar truck.

expert reply by: Michael H

0

Answer 1

When installing the Curt hitch part #C15302 you do need to reuse the factory 14 mm bolts that the factory hitch was using but since you have lost yours you could get replacements from a dealer or find matching bolts at a hardware store.

view full answer...

Answer 2

Yes, the Curt Trailer Hitch #C15302 does have you reinstall your spare tire on your 2010 Chevy Silverado in step 6 of the installation instructions that are attached. If you need a ball mount kit, I recommend #EBMK2416 that comes with a 16K rated…

view full answer...

Answer 3

The best class V hitch for your 2002 Silverado 2500 is going to be the Curt Trailer Hitch item #C15703. This hitch is custom fit for the 2500 HD's with the 6-1/2' beds and bolts to your truck with included hardware. This hitch has a…

view full answer...

Answer 4

Yes, we can help you with new hitch installation hardware for your Curt hitch #C11474. The hitches we offer include complete hardware kits when new, but since hitch installation hardware is single-use only, you will need to use new hardware to…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...