Is Manual Override Plug Available For LCL Powered Jack

Question

Question:

Trying to find a manual override plug on a LCL power jack. Do you have anything similar? Thanks...

asked by: Bill

0

Expert Reply:

Several of the powered trailer jacks we offer have a manual override option.

For example, the Bulldog powered camper jack we offer, part # BD500185, has a manual override feature that uses a crank bolt, part # BD500191. The rubber cover is removed and the crank bolt is used with a ratchet to manually operate the jack when power is lost.

If the plug that covers the override feature is what you are looking for, we offer a cover that works with Bulldog Powered-Drive camper jacks. That part number is # BD500194. If you do not have a Bulldog jack, you may have to contact the trailer manufacturer or the company that built your power jack for a replacement plug.

expert reply by: Jeffrey L

0

Answer 1

Sounds like you have an issue with the nut and screw of the inner leg on your trailer jack. Typically this is a sign that it's time to replace the jack as it has an internal problem. I recommend replacing it with the Stromberg Carlson…

view full answer...

Answer 2

Normally the 12 volt power circuit of a tow vehicle is rated for 40 amps so the answer to your question should be yes, but you would need to check the fuse of the 12 volt accessory circuit on your vehicle to verify if you have the amperage needed…

view full answer...

Answer 3

Yes, the Extreme Off-Road Swing-Up Jack w/ Dual Wheels iItem #ORJW500D will work for your T@B 400 Tear Drop Trailer. It looks like your trailer comes with an a-frame jack. You would need to ensure you have enough space on your tongue to accommodate…

view full answer...

Answer 4

Electric tongue jacks like the 5000 lb-rated Stromberg Carlson #JET-5000 will draw a good bit of power when their motor is operating. It can happen that sometimes the jack will get enough current to light up the jack's high-efficiency LED lights…

view full answer...

Answer 5

You will need the Bulldog Replacement Manual Override Crank Bolt Kit for Bulldog Powered-Drive Camper Jack, part #BD500191. This is a manual override crank bolt that is designed for the Bulldog Jack #BD500185. It does not include a crank handle. The…

view full answer...

Answer 6

You could use a 2-pole connector like the #HM47965 to wire the Fulton XLT Powered Drive Trailer Jack #F141401 to connect to the power and ground wire on the jack and route it to your vehicle battery, but a much easier way is just adding a 7-way…

view full answer...

Answer 7

Great question. You technically could connect the Bulldog Powered-Drive Trailer Jack - Drop Leg - A-Frame - 21-3/4" Lift - 3,500 lbs - White #BD500188 to your vehicle lights, but we do not have the connector you would need to just plug into your…

view full answer...

Answer 8

If the 2 6-volt batteries were wired in parallel which would double their voltage to 12 volts you could use them to power the Stromberg Carlson Electric Trailer Jack #JET-5000 as it does require 12 volt batteries to run. I attached a picture that…

view full answer...

Answer 9

Override plugs are not universal and indeed are specific to certain trailer jacks. The ones we carry are the Replacement Override Plugs for Lippert Smart Jack Electric Trailer Jack #LC733925 which is for the Lippert Smart Jack Electric Trailer Jack…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...