Recommendations For Wiring Fulton XLT Powered Drive Trailer Jack F141401
Question:
Can you use the existing wiring to hook to Andersen 50A plugs or can you change out the wiring to fit a Andersen 50A plugs, are wire to a different plug such as a 4 pole plug etc.
asked by: Richard S
Expert Reply:
You could use a 2-pole connector like the # HM47965 to wire the Fulton XLT Powered Drive Trailer Jack # F141401 to connect to the power and ground wire on the jack and route it to your vehicle battery, but a much easier way is just adding a 7-way connector # PK12706 to the jack wiring so you can power the jack by your tow vehicles 7-way connector.
To do this you would connect the black wire to the 1 o'clock spot when looking at the back of the connector, and connecting the white wire to the 7 o'clock pin when looking at the back of connector.
This jack has a built in 15 amp circuit breaker so it will never pull more than that and since the 12v power circuit on your 7-way has 30 amps minimum you will have no issues using it to power the jack.
You could of course just wire the jack to an on-board battery if you have one, but you will not be able to use the Andersen 50 amp plugs you mentioned as they are designed for 6-gauge wire which this jack does not have.
I included videos of the products mentioned for you to take a look at.
Products Referenced in This Question
Hopkins 2-Pole Flat Wiring Extension - 12" Long
- Trailer Wiring
- Wiring Adapters
- Single-Function Adapter
- 0 - 5 Feet Long
- 2 Pole
- Plug and Lead
- 2 Pole
- Hopkins
more information >
Pollak Black Plastic, 7-Pole, RV-Style Trailer Connector - Trailer End
- Trailer Wiring
- Trailer Connectors
- Trailer End Connector
- Plug Only
- 7 Round - Blade
- Pollak
more information >
Product Page this Question was Asked From
Fulton XLT Powered Drive Trailer Jack - Drop Leg - Side Mount - 22" Lift - 2,500 lbs
- Trailer Jack
- Boat Trailer
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 2001 - 3000 lbs
- Electric Jack
- 22 Inch Lift
- Bolt-On
- With Round Foot
- Fulton
more information >
Continue Researching
- Shop: Fulton XLT Powered Drive Trailer Jack - Drop Leg - Side Mount - 22" Lift - 2,500 lbs
- Video: Fulton XLT Powered Drive Trailer Jack Review
- Shop: InfiniteRule Trailer Coupler Lock - Trigger Latch Style - 1/4" Pin Diameter - 1-1/8" Span
- Q&A: Electric Trailer Jack Recommendation for a 7,500 lb Boat Trailer
- Video: Review of Fulton Trailer Jack - XLT Powered Drive Trailer Jack - F141401
- Q&A: Dimensions Of Head Assembly Of Fulton XLT Power Jack F141401
- Search Results: battery box
- Shop: Square Pipe Mount Swivel Jack w Footplate - Drop Leg - Weld On - Sidewind - 28-1/2" Lift - 7K
- Q&A: Amperage Draw For Fulton XLT Powered Trailer Jack and is Circuit Protection Needed
- Q&A: Backup Brake Battery for Powering Trailer Jack
- Q&A: How To Tell The Difference From Right and Left Electric Brake Assemblies
- Shop: Replacement Clamp-On Battery Box for Tekonsha Trailer Breakaway Kit
- Shop: Curt Fusion Ball Mount for 2" Hitches - 2" Ball - 2-1/4" Rise - 7,500 lbs
- Shop: Buyers Products Tail Light Mounting Box - 6" Oval Hole - Black Powder Coated Steel
- Shop: Yates Keel Roller for Boat Trailers - TPR - 12" Long - 5/8" Shaft
- Search Results: light box
- Search Results: hitch receiver adapter
- Search Results: tail light box
- Search Results: 12 volt breakaway battery
- Search Results: high temp bearing grease
- Search Results: tjdp~7000s~b
- Q&A: Installing Trailer Mounted Battery to Power Trailer Tongue Jack
- Q&A: How To Install a Battery On a Trailer for Use with Electric Jack
- Video: Pollak Black Plastic 7-Pole RV-Style Trailer Connector Review
- Video: etrailer Trailer Jack - Side Frame Mount Jack - TJD2SP-12000SP-F Review
- Video: etrailer Landing Gear Set Review
- Shop: Trailer Wiring
- Video: Bulldog Camper Jack - A-Frame Jack - BD500187 Review
- Video: Review of Fastway Trailer Jack - Camper Jacks - FA88-00-6500
- Shop: Vehicle Tow Bar Brake System