U bolts Recommendation for Use with the CE Smith U-Bolt Bolster # CE10192GA-4

Question

Question:

What are the correct size and width ubolts to use with this bracket on a 3 inch square frame? Thanks

asked by: Scott C

0

Expert Reply:

The recommended U-bolts to use with the CE Smith Double U-Bolt Bolster and Swivel Bracket Assemblies # CE10192GA-4 are the CE Smith U-Bolts # CE15283GA-8 which are 3-13/16" Long x 3-1/16" Wide x 1/2" Diameter.

expert reply by: Jameson C

0

Answer 1

After speaking with my contact at CE Smith, I found the CE Smith Pyramid Washer #CE10806 fits against the nut high side up. To demonstrate how this would work, I have included a video that should be helpful. This washer works best with the CE Smith…

view full answer...

Answer 2

I went and pulled CE Smith Double U-Bolt Bolster and Swivel Bracket Assemblies #CE10192GA-4 from our warehouse to get the dimension you are looking for and found it to be 5 inches from the top of the bracket down to the nearest part of the u-bolt…

view full answer...

Answer 3

The #CE10002G-4 CE Smith Bolster and Swivel is 13" tall. Assuming you mount it at the position to gain the most height, you should have 9" remaining. Losing the height from attaching to the 3" crossmember leaves you with 10"…

view full answer...

Answer 4

I took the following measurements for the CE Smith Bolster and Swivel Bracket Assemblies #CE10001G-4 and the CE Smith U-Bolts #CE15283GA-4 that would fit a 3" crossmember. From the top of the swivel bracket to the inside of the U-bolt(top of…

view full answer...

Answer 5

To be on the safe size, I recommend going with a 13 inch bracket #CE10002G-4 at the back of the trailer and an 11 inch bracket with #CE10003G at the front. A nice feature on these brackets is that they will each actually have as much as 3-3/4 inches…

view full answer...

Answer 6

The terms bolster bracket and bunk bracket refer to the same thing. For example, CE Smith part #CE10002G-4 is a bracket that can be used on a boat trailer to mount either a standard carpeted wooden bunk board (that supports the boat's hull) or a…

view full answer...

Answer 7

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 8

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Answer 9

That is an excellent question and is asked more often than you think. Electric brakes like what come in the Electric Trailer Brake Kit #AKEBRK-2 can be submerged in water when you are loading/unloading your boat. Since water and electricity don't…

view full answer...

Answer 10

Your trailer looks awesome! The Road armor equalizers #LC696740 and Equa-Flex Cushioned Equalizers #LC279687 are both pretty similar in performance even though the Road Armor has two dampers. The main difference is the size of the equalizers. The…

view full answer...

Answer 11

I looked up the dimensions of your High Pointe EC942K9E and it's 15 inches deep, 15.7 inches tall, and 29.9 inches wide so the Furrion Over the Range RV Convection Microwave #FMCM15SS would easily fit in place of it and would also work really…

view full answer...

Answer 12

The LaSalle Bristol XTRM Self-leveling Sealant part #34427034145-1 is very comparable to the Dicor 501LSW self leveling lap sealant. I can't say exactly what the formula is for Dicor but I can tell you that LaSalle Sealant is a silicone sealant…

view full answer...

U bolts Recommendation for Use with the CE Smith U-Bolt Bolster # CE10192GA-4

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching