Operation Instructions for Tekonsha Voyager Brake Controller # 39510

Question

Question:

Can you email me a copy of the instructions, that come with the voyager xp? I had my truck cleaned and they moved the settings and I cannot get it set back properly. Thanks in advance.

asked by: Mike R

0

Expert Reply:

The installation and operation instructions for the Tekonsha Voyager brake controller # 39510 are linked for you. I've also linked a review video for this product.

expert reply by: Adam R

0

Answer 1

There are a few differences between the two controllers. The Voyager has been around for a looooooooong time. It uses an internal pendulum to determine how quickly the tow vehicle is braking. In order to operate correctly, this level of the pendulum…

view full answer...

Answer 2

I have attached a basic brake controller wiring diagram for you. You will want to make sure that you ground the white wire to the negative post on the battery. The black wire will attach to the positive battery post. The red wire will tap into the…

view full answer...

Answer 3

The brake controller installation on your 2006 F150 is pretty easy. The connector for the brake controller is located under the dash, behind and to the right of the OBD port as shown in the video I've linked for you. You'll need the brake…

view full answer...

Answer 4

The plug that you have attached a photo of is the correct one that will need to be used in order to install a brake controller on your 2007 Ford F-150. If you take a look at the square end of the Tekonsha Plug-In Wiring Adapter for Electric Brake…

view full answer...

Answer 5

Just by the date I cannot determine which controller it is because there were different models at that time. If it is a Voyager then it could be either a 9030 or a 9035. The 9030 was designed for up to 2 axle trailers (4 brake assemblies maximum).…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Operation Instructions for Tekonsha Voyager Brake Controller # 39510

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching