Would the Optronics Trailer License Plate Bracket part # LP15SB Replace a Wesbar 003201 Bracket

Question

Question:

will this replace a wesbar 003201 ?

asked by: Richard F

1

Helpful Expert Reply:

The Wesbar license plate bracket part number 003201 that you referenced is a universal license plate bracket just like the Optronics Trailer License Plate Bracket part # LP15SB.

To see if the mounting holes would line up check out the dimension picture I attached. If the dimensions don't match up you could still make the bracket work pretty easily.

expert reply by: Jameson C

1

click to enlarge

Answer 1

I attached a picture that shows what type of lighting requirements are needed for a trailer over 80 inches in width as well as a link down below that covers this as well.

view full answer...

Answer 2

Yes, you can power and ground the LED license plate light #LPL91CB using the 7-Way trailer connector. The power wire would run to the running light circuit and ground to the ground circuit. If you wanted to wire those up to a trailer-side 7-Way you…

view full answer...

Answer 3

Yes, the disc of the 7-Piece Installation Set for Bearings #PTW83020 that measures 1.965 inches would be the correct one to use with a race part #L44610. I attached a review video for this that shows how it works as well.

view full answer...

Answer 4

From the information that I was able to find on the L44549 bearing, it shows it being a 1-1/16 inch bearing which is the same as Trailer Hub Bearing, #L44649. Just to be sure, I recommend measuring the L44549 bearing with a digital caliper to confirm…

view full answer...

Answer 5

Since you have a C hook type spring you really need to replace it with another C hook unless you are okay with replacing all of the spring components. We only have one c hook spring as of right now part #e33SR, but it has a 4,100 lb axle capacity and…

view full answer...

Answer 6

The DeeMaxx Disc Brake Kit #DE28YR does not have the E-Z grease fitting, you'd want to take a look at the Kodiak Disc Brakes #KOD69FR instead. This brake assembly is the same thing as #DE28YR but also includes 2 hub-rotor assemblies with…

view full answer...

Answer 7

We have that size (see link), but none of the tires are radial. They are all bias ply as that is the common construction for the LT tires. The closest tire size that is radial would be the 235/80R16 like part #TTWTRTM2358016E. This size has a section…

view full answer...

Answer 8

We have ramps that will work perfectly for loading your 1690lb UTV into the bed of your truck. I recommend the Arched Loading Ramp Set #288-07432-2 which is 90" long x 18" wide and has a combined weight capacity of 3000lbs. The included…

view full answer...

Answer 9

The Dexter 8-283 is an obsolete 2800lb 10 x 1-1/2 inch hub that used a LM67048 inner and a L44649 outer bearing. Unfortunately, we don't have any hubs that would be compatible with the spindles on your axle. Your best bet at this point would be…

view full answer...

Answer 10

To wire in the reverse light wire on Curt 7-Way connector #C57102 for the back up alarm to work you will need to tap into a reverse light wire behind a reverse light on your 1999 Dodge Ram. If you do not wish to tap into the wire there then you can…

view full answer...

Answer 11

Yes, I attached an install video that shows the Pollak part #PK12-707E (same as number you mentioned) installed in a newer GMC to this page.

view full answer...

Answer 12

The Rubber Lube Plug - Fits 1.18" Lubed Dust Cap #DC-RP is the replacement for the #RG04-040 grease cap as well as larger caps like the 2.44" OD Drive In Grease Cap with Plug #RG04-080. The Grease Cap Plug fro E-Z Lube Grease Caps is the…

view full answer...