Dimensions of Replacement Rubber Grease or Oil Cap Plug

Question

Question:

Do you offer a plug to fit a 13/16 inch hole?

asked by: Joe

0

Expert Reply:

The Rubber Lube Plug - Fits 1.18" Lubed Dust Cap # DC-RP is the replacement for the # RG04-040 grease cap as well as larger caps like the 2.44" OD Drive In Grease Cap with Plug # RG04-080. The Grease Cap Plug fro E-Z Lube Grease Caps is the same size and is part # RG04-010.

We have the Dexter Oil Cap plug with is much smaller at 0.55 inch diameter and the other Dexter oil cap plug that is bigger # 46-32 which is 0.88 inch diameter.

The Replacement Center Plug for Kodiak XLProLube Oil Bath Cap - Qty 1 # XLPROLUBE-PLUG has a diameter of 0.5 inch.

Because these are all rubber plugs, the # 46-32 will most likely work for your 13/16 inch hole to give you a tight seal.

expert reply by: Jason S

0

Answer 1

To get you the correct Bearing Buddy grease caps you will need more information. The info on the trailer sticker even if it wasn't so faded would not have helped. You will need to simply pull one of your grease caps and use a digital caliper to…

view full answer...

Answer 2

Yes, I attached an install video that shows the Pollak part #PK12-707E (same as number you mentioned) installed in a newer GMC to this page.

view full answer...

Answer 3

To wire in the reverse light wire on Curt 7-Way connector #C57102 for the back up alarm to work you will need to tap into a reverse light wire behind a reverse light on your 1999 Dodge Ram. If you do not wish to tap into the wire there then you can…

view full answer...

Answer 4

The Tie Down Engineering (TDE) Brake Actuator 48980 also known as the 80LP/85LP is a 8,000 lb or 8,500 lb disc brake actuator with 2" coupler. In order to replace this, the best option we have is the Demco Hydraulic Brake Actuator part…

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

It's hard to see the diameter of your cap in the picture you submitted but it appears you need the part #DC-RP which fits a 1.18 inch diameter hole like it looks like you have.

view full answer...

Answer 7

A grease seal like the part #GS-2250DL would be your best option if that is the size you need. You can go to an oil seal like with the Unitized Oil Seal for Trailer Hubs #10-63 which is same size and it would work but it's not going to be…

view full answer...

Answer 8

On the frame of your trailer, near the coupler, there should be a plate that has axle information such as brand and capacity. There also should be information on the axle itself somewhere. Between checking those two places you should be able to track…

view full answer...

Answer 9

You will want to use a dial caliper or micrometer like part #PTW80157 to measure the inner diameter of the hub you have on your trailer to determine what size cap would be needed. Check out the picture I attached that shows this measurement being…

view full answer...

Answer 10

There is basically no difference between dust cap set #RG04-020 and single cap #F001518 other than #F001518 is a single unit and #RG04-020. They otherwise have the same dimensions just from two different manufacturers.

view full answer...

Answer 11

I would recommend to remove and reinstall the complete trailer hub assembly to make sure all of the parts are installed properly. I am including a link to a video of how to remove and reinstall a trailer hub on a boat trailer. This video will show…

view full answer...

Answer 12

I do have an option for you but the Rubber Lube Plug part #DC-RP that you purchased is designed to fit a 1.18" diameter opening and will not work for you assuming the plug you measured is indeed 1.5" diameter. Instead, the better option for…

view full answer...