Could the Redline 2-Way Pop-Up Roof Vent part # 9106-2756 Be Installed with Rivets

Question

Question:

There is no reason why you could not install the # 9106-2756 on the side of the trailer..... Can the vent be mounted with pop rivets to the side of an aluminum skin trailer? Additionally, what does the vent weigh in pounds?

asked by: Dave

0

Expert Reply:

Rivets could definitely be used to install the Redline 2-Way Pop-Up Roof Vent part # 9106-2756. Using a silicone sealant like part # 0160297 is recommended to prevent water intrusion.

The vent weighs 5 lbs.

expert reply by: Jameson C

0

Answer 1

The recommended screws for installing the part #9106 that you referenced is the #31071. This would work well on a sheet metal trailer wall/roof. The garnish part #2756 would then fit over them just fine.

view full answer...

Answer 2

The Redline 2-Way Pop-Up Roof Vent, part #9106-2756 adjusts in steps from fully closed to keep rain or air out, to fully open to let fresh air in. This vent can be installed with the vent facing either direction and being able to open the vent toward…

view full answer...

Answer 3

Yes, I have messed with the Redline 2-Way Pop-Up Roof Vent #9106-2756 on several occasions and you can open it easily from the outside of the trailer.

view full answer...

Answer 4

I don't see any reason you couldn't use the Redline 2-Way Pop-Up Roof Vent with Garnish for Enclosed Trailers #9106-2756 in the metal window panels of your Ford Transit Connect. People install these on similar surfaces pretty frequently…

view full answer...

Answer 5

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Answer 6

I can certainly point you in the right direction. I will say that we only deal with round tube leaf spring axles, so I am afraid we cannot provide a replacement axle. We do offer the 12" x 2" brake assemblies #23-112-113 which have built in…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 9

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...