Front Tie Downs for Slide-In Truck Bed Camper for a 2014 Chevy Silverado 2500 Short Bed

Question

Question:

Will these fit the short bed

asked by: Gayle S

0

Expert Reply:

We have Tork Lift tie downs # TLC2220 as the option for the front tie downs on the 2014 Chevy Silverado 2500 short bed. They will fit the following:

6-1/2 Foot Bed Crew Cab without board or step underneath truck bed and without a hitch
6-1/2 Foot Bed Crew Cab without board or step underneath truck bed and with a Torklift SuperHitch
6-1/2 Foot Bed Crew Cab without board or step underneath truck bed and with a factory installed hitch
6-1/2 Foot Bed Crew Cab without board or step underneath truck bed and with a non-Torklift aftermarket hitch

For the correct rear tie downs I would need to know the cab style, if the truck has running boards that extend past the cab, and if the truck has a hitch and if so what brand (or factory if it is factory). There are currently no options for models that are no a crew cab. I have included a link to the Tork Lift tie down main page for your truck. Use the drop down menu to select the version that describes your truck.

expert reply by: Michael H

0

Answer 1

In order to pick out the correct TorkLift tie down brackets more information would be needed from you. I would need to know bed length, cab style, single or dual real wheel configuration, plus all the information you listed. Or you can follow the…

view full answer...

Answer 2

For the TorkLift Custom Frame-Mounted Camper Front Tie-Downs #TLC2220 the 1/2-inch bolt that is to be installed in the hole in the bottom of the front spring perch should be placed using the included coiled bolt fisher wire. Insert the coiled end…

view full answer...

Answer 3

The TorkLift options for your truck are the #TLC2220 for the front and #TLC3215 as long as your steps do not run under the bed. If they end at the cab, then these will work. If they do run under the bed, then instead you will want the HappiJac…

view full answer...

Answer 4

The TorkLift Custom Frame-Mounted Camper Tie-Downs #TLC4204 (front) and #TLC3212 (rear) will fit your dually 2011 Chevy Silverado 3500 Crew Cab with an 8 foot bed, cab-length running boards and a factory hitch. I have added a photo of these…

view full answer...

Answer 5

On your 2014 Chevrolet Silverado 2500 HD, when installing the TorkLift Custom Frame-Mounted Camper Tie-Downs, part #TLC2220, and part #TLC3212, there is no drilling required for installation. This tie-down system is designed for trucks with a 6-1/2…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 9

The proper extension for your setup would be the one that allows you to have clearance of your hitch mounted accessory and also allows you to still be able to pull the steps down. If the receiver tube sticks out past the camper too far then you…

view full answer...

Answer 10

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 11

There is not a plug and play adapter for your Lance connector that we are aware of. Typically this is installed by the Lance dealer. A junction box/7-way plug kit like #HS381-9000 is an option you have to convert the camper to match the 7-way RV…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Front Tie Downs for Slide-In Truck Bed Camper for a 2014 Chevy Silverado 2500 Short Bed

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching