Weight Capacity for the Erickson Big Bed Load Extender

Question

Question:

The description notes a 400 lb.limit. Is that for a bed distributed load or a full load weight?

asked by: John M

0

Expert Reply:

The 400 lb limit would be for bed distributed loads. Basically, if what you are carrying weighs less than 400 lbs the Erickson Big Bed Load Extender # EM07600 that you referenced would work for you.

Check out the review video I attached for this product for you to check out also.

expert reply by: Jameson C

0

Answer 1

The Erickson Big Bed Load Extender, #EM07600, measures 49-1/2 inches from the hitch pin hole to the outer edge of the upright. I have included a picture to illustrate this measurement. To determine exactly how far the extender, #EM07600, will extend…

view full answer...

Answer 2

The Erickson Big Bed Load Extender #EM07600 has crossbars which are 48-1/2" when in use, and that dimension does not include the wings - or tie-down points - at the end of the crossbars. The 48-1/2" is usable space, so your 4' wide…

view full answer...

Answer 3

According to my Erickson representative, their Big Bed Load Extender, part #EM07600 is 48-3/4 inches long, measured from the hitch pin hole to the rear surface of the upright, as shown in the provided photo. If you click the provided link, you can…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

Hey Jason, I spoke with Furrion and they stated that the Furrion Chill Cube is OEM only currently and should be released to the aftermarket distributors later on this year (2024), but there is no solid date. That says to me that they're probably…

view full answer...

Answer 11

Since the bolt holes line up vertically and horizontally you'll be able to bolt the Trailair Air Ride 5th Wheel King Pin - Leland 7920 #UF35-946208. This specific pin box actually has an 18" king pin to first set of bolt holes measurement…

view full answer...

Answer 12

If one set of the HappiJac Extender Brackets part #HJ54FR doesn't provide enough clearance Happijac has told us that you can use a second set to gain additional clearance.

view full answer...

Weight Capacity for the Erickson Big Bed Load Extender

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching