How Far will Erickson Big Bed Load Extender # EM07600 Extend Past Hitch on Toyota Tacoma 5 FT Bed

Question

Question:

I have a Tacoma with a 5 foot bed. I want to carry a 14 foot canoe so I need to know how far past the trailer hitch the extender reaches.

asked by: John S

0

Expert Reply:

The Erickson Big Bed Load Extender, # EM07600, measures 49-1/2 inches from the hitch pin hole to the outer edge of the upright. I have included a picture to illustrate this measurement.

To determine exactly how far the extender, # EM07600, will extend past the hitch of your Toyota Tacoma, you will just want to measure out 49-1/2 inches from your hitch pin hole.

expert reply by: Leah S

0

click to enlarge

Answer 1

The 400 lb limit would be for bed distributed loads. Basically, if what you are carrying weighs less than 400 lbs the Erickson Big Bed Load Extender #EM07600 that you referenced would work for you. Check out the review video I attached for this…

view full answer...

Answer 2

For a truck bed extender with a bar wide enough to carry and haul something that is 38 inches wide you could use the Flint Hill Goods Truck Bed Extender - 2" Hitches #FHG89ZR which has a load bar that extends up to 48 inches wide.

view full answer...

Answer 3

The Erickson Big Bed Load Extender #EM07600 has crossbars which are 48-1/2" when in use, and that dimension does not include the wings - or tie-down points - at the end of the crossbars. The 48-1/2" is usable space, so your…

view full answer...

Answer 4

The length of the truck bed extenders like the Erickson Big Bed Load Extender for 2" Hitches part #EM07600 are not adjustable. That said, all you would need to do is move the load away from the cab in order for it to rest on both the bed floor…

view full answer...

Answer 5

The Rhino-Rack T-Load Hitch Mounted Load Assist and Support Bar #RTL002 does use the Hitch Lock #RRRBCA025.

view full answer...

Answer 6

You certainly can install two pairs of the Ark Drop Down Corner RV Stabilizer Jacks #ARK77FR on your trailer. In that case we recommend adding one jack to each corner of the trailer frame. Keep in mind that these are designed to stabilize, not lift…

view full answer...

Answer 7

There is no reason why you couldn't install a front mount hitch and and add a front load bar to help support your Kayak and create more clearance between it and your travel trailer. The front mount hitch I recommend for your 2007 Toyota Sequoia…

view full answer...

Answer 8

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 9

If you are getting a 2" hitch receiver installed on your 2022 Hyundai Santa Cruz, you will not need any adapters to install the Erickson Big Bed Load Extender for 2" Hitches - 400 lbs, part #EM07600. I have included a video review link…

view full answer...

Answer 10

The simplest and best way you'll be able to carry a kayak on the roof of your 2017 Chevy Colorado Crew Cab will be with a roof rack and roof rack kayak carrier. A ladder rack won't fit with the headache rack you have which so with a solid…

view full answer...

Answer 11

The lowest setting of the Erikson Big Bed Load Extender #EM07600 is 18" in height while the lowest setting of the Yakima LongArm Truck Bed Load Extender #Y01149 is measured at 17" high. That will still bring you at an inch higher than your…

view full answer...

How Far will Erickson Big Bed Load Extender # EM07600 Extend Past Hitch on Toyota Tacoma 5 FT Bed

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching